Automatic chicken feeder. Automatic bird feeder with interchangeable cassettes

Designed only for feeding with dry feed, which are characterized by flowability. It is possible to pour grain, granules, compound feed into the container, but in no case can you add various mixers or grated vegetables.

These devices can be various kinds, but they are based on the same principle of operation.

Thanks to the operation of the feeders, chickens are fed automatically, exactly in the volume that was consumed by the birds. Another part of it is contained in an individual compartment of the mechanism.

The advantage of the automatic feeder is not only in the continuous supply of birds with food, but also in its protection from scattering and soaking during the rainy season. Also, these devices save feed well, due to the correct dosing.

Attention is drawn to the automatic feeder, which can be programmed, as well as having a timer. With the help of the timer it is possible to set the feeding time. The feeder has an auger that moves the feed into the tray. Almost all models of devices with a timer have a backup battery and a container for storing feed mix. The frequency of feeding is possible up to eight times, the break between them is also adjustable.

The feed compartment is perfectly protected, due to the tightly closed lid. Due to the fact that the tray is removable, it is very easy to clean. The main disadvantage of this device will be a very high price.

Options for sale

In specialized stores and online stores, it is possible to buy both simple devices, for example, a bunker, and high-tech devices with a timer and a feed spreading function.

The cost of simple ones varies from five hundred to one and a half thousand rubles, while the latter will cost five to six times more.

The material of these devices is different: from ABS plastic (cost about six and a half thousand rubles) and to powder-coated steel (eight and a half thousand rubles).

Where to begin?

You can actually make an automatic feeder with your own hands from a wide variety of materials. Most often they use wood, plywood or plastic.

In order to independently make an auto-feeder, the following materials and tools are needed:

plywood sheet;
wooden bars;
bolts for furniture;
loops - 2 pcs.;
saw for wood;
drill, drill;
pencil;
roulette.

A To make your own, you need the following materials and tools:

a plastic container (volume from five to ten liters), while a bucket, bottle or other type of container can perform the function of a bunker (read about how to make a chicken feeder yourself from a plastic 5 liter bottle);
well-sharpened knife;
a plane with a side;
nails;
self-tapping screws;
wire.

How to do it yourself?

With dispenser

When all the materials are prepared, then you can start manufacturing. The procedure is as follows:

On a sheet of plywood, it is necessary to draw the details of the structure. There should be seven of them:
- front part - two rectangles 28 * 29 centimeters and 7 * 29 centimeters;
- cover - rectangle 26 * 29 centimeters;
- side walls - two pieces, height 40 centimeters, upper edge 26 centimeters and lower edge 29 centimeters;
- bottom - rectangle 29 * 17 centimeters;
- back wall - 41 * 29 centimeters.
Carefully cut out the details.
Next, make holes for the screws in the attachment points with an electric drill.
In order to make the surface of the feeder safe for chickens, process all the details with sandpaper.
Assemble the structure. It must be remembered that the front upper and rear walls should be located relative to the horizontal at an angle of 15 degrees.
Hinge the top cover to the back of the side walls.

We watch a video on how to make a do-it-yourself plywood automatic feeder for chickens:

Bunker model

At the beginning, you need to choose a container into which the feed mixture will be added, as well as lower part.
As a tray, it is possible to use a lid that has edges or any container for growing seedlings.
It is necessary that the bottom diameter be bigger size by 20-30 centimeters, in contrast to the feed bunker.
Next, you need to cut a semicircular hole, with a radius of about 4-5 centimeters, for each compartment, using a knife.
Then, using self-tapping screws, connect both parts of the parts.
In order for the feeder to have correct location on required level and to ensure maximum convenience for the birds, nails and long wire should be used. When total absence the need for this and the bird feeder turned out to be quite strong and stable, it is enough to put it in the chicken coop on the floor.

Photo

How to use?

All these devices, made independently or purchased in stores, are designed to supply food to birds when they completely eat it.

The poultry breeder is obliged all the time to add food for his winged pets to a place specially designated for this, that is, to the compartment in which food is added in portions. This place must be tightly closed - this will save all the food from quickly eating it by all birds, especially violent ones, for example, Andalusian breeds of chickens, and will prevent the food from being scattered all over the chicken coop.

So that the bird rushes and does not get fat, then you should not overfeed it too often. In order for the bird not to get sick and always be in excellent condition, it is necessary to observe its proper diet. To date There is a wide variety of pet foods available..

The meat will be juicy and soft, and the eggs will be healthy and rich in trace elements, if the bird receives the right and healthy diet. It is very important to comply proper nutrition in birds. Although you need to feed the bird all the time, there are still situations when you need to limit the dose of food in chickens. Most often, the need for such a procedure arises when eggs are formed in chickens.

Young chickens should not be allowed to lay eggs, as these birds can have serious health problems. If chickens have problems with bones or their structure, then this indicates that its nutrition is of poor quality or monotonous.

Conclusion

Automatic has been very popular and loved among all poultry farmers for a long time. It is better not to use overly expensive production models in small economic enterprises, since they can be quite ineffective.

You should not be upset prematurely. You can always make an automatic feeder for your birds on your own, at home, and this is done quite simply. In creating it yourself, there are two pluses: you can make it to your taste, color and spend a minimum of money on it.

Winter is on the way, it is harder for poor birds to get their own food every day. Let's help them, at the same time teach our children kindness and mercy, care for our smaller brothers. Grateful birds in return will delight you with unpretentious but cheerful songs, as well as sketches from their bird life. If you put a video camera next to the feeder, you can eventually get an exclusive story in the style of "In the Animal World" and show it at school in the lesson of the world or biology. In general, in this article we decided to talk about what should be a bird feeder that you make with your own hands. We will offer a description and a photo.

Making a simple do-it-yourself feeder

First of all, inspect the intended material, from which you plan to make a feeder, and estimate your capabilities. Also consider some design requirements:

Remember, it should be comfortable for the birds, as well as for pouring and removing food.
She must have protection from wind and precipitation, the wind can simply bring food out, and precipitation can cause food to freeze or mold, which is also inconvenient for the birds.
The material from which the feeder is made must be moisture resistant, so that it would not have to be repaired or remade several times during the winter.
It should not have sharp edges and corners, so as not to injure the birds.
If it is supposed to feed small birds, then the feeder should also be made small so that large and aggressive birds do not rob it and scare away small birds.
It is better to place your feeder on tree branches or fix it on the walls of a house or household. buildings, not lower than one and a half meters from the ground, so that the cats do not get there, and it is convenient for you to replenish food supplies.

plywood option.

Of course, you can buy it ready-made in the hypermarket. But to make it yourself, and even together with the children - what could be better if the sons help you, and the daughters look with different eyes at such a handmade father! Moreover, there are no difficulties here. It can be made closed, open, with a gable roof. On the Internet, you can easily find any drawings with ready-made sizes and patterns. Choose any!

For small birds, it is necessary to take into account the dimensions of the structure, so that it would not even occur to the big voracious crows to poke their heads there, they will simply be very uncomfortable there.

So, prepare a jigsaw, a hammer, suitable cloves, sandpaper, water-based glue, plywood, a 20X20 cm bar for work. Let's start with the simplest option.
We make the bottom 25X25 cm, and the roof is larger so that the water flows past without getting inside. We mark the rest of the details according to the patterns on plywood.
With sandpaper, be sure to sand the sawn edges properly so that there is no burr left.
We cut the bar into 4 racks 25 - 30 cm long.
If you plan to make the roof flat under a slope, then make 2 bars out of 4 shorter by a couple of cm, and under a slope.
We first glue all the connecting places with glue, and then we fasten them with carnations. We attach racks to the bottom, and sides to them.
We fix the roof with self-tapping screws on top of the racks.
Now it remains to fix the feeder in the chosen place, and fill the treat there.

Variants of a wooden feeder.

This is a more durable material. If you have the skills to work with wood and tools for its processing, feel free to get down to business. A board for work will need a thickness of 18 - 20 cm, in addition, prepare a bar 4.5X2 cm, a square piece of plywood 25X25 cm (the bottom of the feeder), and for the roof 2 pieces of 35X22 cm each, as well as self-tapping screws, glue and cloves.

Homemade - a feeder from a milk bag / box.

Here we are talking about how to make a bird feeder. The next option is the most elementary. He is tough even for a child. We take:

Clean package / box of juice or milk.
Wire or rope made of nylon for hanging.
Marker.
Adhesive plaster.
Stationery knife or scissors.

First, outline and cut on opposite sides ah bird holes. We protect the cut edges with adhesive tape so that the birds do not cripple. We pierce holes under the holes and insert the trimmings rolled up from the bird holes there, and above the holes we make holes for wire or rope for hanging. We fasten our feeder to a branch.

It can also be attached to a tree, but then it is necessary to make holes not from opposite sides, but from close ones, to facilitate the approach of birds.

There is a variant of the feeder of two packages, it turns out to be triangular in shape. We cut off the first package by 2/3 and cut out the front side at the bottom, this will be the bottom. And we cut the second package from the bottom along the narrow sides, but do not touch the top. Now we combine both parts and fix them with glue or tape.

Feeders are also obtained from 1.5 - 2 liter bottles.

Option 1. On opposite sides of the bottle, cut out holes of arbitrary shape. When cutting holes in the shape of the letter P, you can bend up the unfinished part, you get a canopy from the rain. Be sure to glue an adhesive plaster or tape from below to the cuts from damage to the bird's paws. You can make holes in the bottom and insert sticks, this will be a perch.

It can be attached to a tree, and hung on branches, if in a lid with inside tie a rope in knots in the holes to make a loop that must be thrown over the branches.

Option 2. The feeder is a bunker. The most summer option if you visit there only on weekends. Then it will not be necessary to monitor the replenishment of food every day, he himself will fall asleep gradually as he eats.

To do this, take a couple of identical bottles. We make holes near the bottom of one bottle. Remove the top part. At the top we cut a symmetrical pair of holes for further hanging. At the second bottle, we make several holes at the neck, a supply of food will pour in there. You should not make large holes right away, then expand them as needed. Now we fall asleep actually, feed, insert into the first cut bottle.

Option 3. Feeder with spoons. We make holes in the lid and insert a rope in the form of a loop there. Next, we make symmetrical holes for spoons. On the side of the cup, we make a larger hole, so that there would be the possibility of spilling the food. It remains to fill the feeder and hang.

In the bottom of any bottle feeder, it is advisable to make several small holes in size with a red-hot needle or nail to remove moisture.

Bird feeder from a five-liter bottle.

Bird feeders can be created not only from wood. For you, we offer products that were created from other available materials. The feeder looks very interesting. for birds from a plastic bottle. Spending one evening and feeding the birds all winter - isn't that useful activity for a rainy autumn evening! There is a five-litre bottle in every house, and a considerable number of birds can easily get enough of such a container. The main thing is to make more holes.

The whole family can take part in the manufacturing process, you need to prepare a pruner, bottle, knife, wire or rope to attach to a tree.

First, we decide how the feeder will be attached to the tree, after that we mark the future holes.

If it is placed vertically, then we retreat 5-7 cm from the bottom and make several square or triangular holes.

If it is horizontal, then we cut wide holes in the neck and in the bottom of the bottle.

Wire or twine will perfectly secure the feeder to the tree. In order to prevent the wind from swaying it, you can put a quarter of a brick on the bottom, and already pour food on top.

Such a large bottle can also be adapted as a bunker option. Then, in addition to the 5-liter, you will need 2 1.5-liter bottles, a marker, a knife and a rope.

We mark holes for birds on a 5-liter bottle, a couple, and one more for a one and a half liter bottle.
We make the hole for the bottle P - shaped, bend the visor up, and seal the cuts with adhesive tape.
At a one and a half liter bottles, we make holes at the points of contact with the bottom of five liters and a little higher, for spilling food to the bottom as needed.
We cut a hole in the lid of a five-liter bottle so that the neck of a one and a half liter bottle would peek out from there.
From the second one and a half liters we cut off the neck in the form of a funnel, and put it in the protruding neck of the first 1.5 liters.
Everything is ready, it remains to fix the bird's dining room on the tree.

An excellent feeder will turn out from a shoe box.

A shoe box or similar in size, can be laminated, made of thick cardboard, suitable for making a feeder. Everything is already there - the roof, the bottom, the walls, the minimum work remains - to cut the necessary holes and attach to the tree. Here you need a clerical knife, a marker and tape with a cord. In the absence of lamination, tape will help protect the feeder from the weather. The bottom must be weighted with sand or pebbles, so that it does not sway with the wind, and after pouring food, hang it on a tree.

There is another option - we fix the lid with adhesive tape perpendicular to the inside of the box, the lid will actually be a table with food, and the box will be both a roof and a side. We make a hook from the wire, and piercing the top of the feeder, we hang it to the chosen place. It remains to pour food and arm yourself with a camera or video camera!

Many chicken farmers are thinking about automating the feeding process. Thus, you can save a large number of time and effort, and pets will always be full. The best option for this there will be an automatic feeder, which for chickens can be purchased or made by yourself. How to make such a device yourself, find out with us.

These devices are different types, but they are based on the same principle of operation. With their help, feed is automatically supplied to the birds, and in the amount that was consumed by the chickens. The rest of it is stored in a separate closed compartment of the structure.

The advantage of an automatic feeder is not only in the constant supply of food to the chickens, but also in its protection from scattering and getting wet during rainfall. In addition, with the help of such devices, you can save a lot by using the correct dosage of feed.

It should be noted that the automatic feeder for chickens is used only for supplying dry feed composition (grain, compound feed). It can be made by hand from a variety of different materials. Most often, wood, plywood or plastic are used for these purposes. You can also buy more complex designs that are equipped with a timer or dispenser.

With timer

The programmable automatic feeder with a timer deserves special attention. It is designed to serve dry food. With the help of such a device, pets will always be fed on time. Feeding the right amount of food will ensure that the hens are properly fed and the feed is preserved.

Using the timer, you can set the time for serving food. The feeder has an auger through which the feed moves into the tray. Almost all models of automatic feeders with a timer are equipped with a backup battery and a tank for storing feed mixture. The number of feedings can be up to eight times, the interval between them is also adjustable.

The lid of the feed compartment closes tightly, so it is well protected. The tray is easily removed, which does not cause any problems in the process of cleaning it. The only disadvantage of such a device is the rather high cost.

We make an auto feeder with our own hands

To save money, you can make an auto feeder with your own hands. According to the method of feeding, they are of the following types.

Tray. These are flat containers equipped with sides so that the food does not crumble. Most often used for feeding chickens.
Grooved. In this case, the tray is equipped with a removable grid, and there are several mixing tanks inside different types stern.
Bunker. The dry mixture is poured into the hopper, which enters the tray as needed. The design well protects food from getting wet and pollution.

Consider some of the most popular models of automatic chicken feeders that you can make yourself. One of the manufacturing options we suggest you look at the video from the author Aksenova Julia.

Feeder with dispenser

This model was invented by an Australian farmer. It is designed for feeding small livestock. If you plan to keep a large number of chickens, then you can make more of these automatic feeders. The peculiarity of this model is to provide access to food by pressing the pedal. Under the weight of the chicken, the lid of the tray opens, where the feed mixture is poured.

Tools and materials

This type of feeder is easy to make with your own hands, for this you will need the following:

plywood sheet;
wooden bars;
bolts for furniture;
loops - 2 pcs.;
saw for wood;
drill.

Step-by-step instruction

If the materials are collected, then you can get to work. The algorithm of actions is as follows.

On a sheet of plywood, it is necessary to draw the details of the structure. There should be ten of them (two covers, two side and one back walls, a bottom, three front bars and a pedal).
Next, you need to cut the bars. The two elements should be the longest, as they will be required to attach the pedals. Two more bars are needed in small sizes to secure the lid. The last two elements should be the shortest. They will be required to connect the bars of the cover.
The walls of the feeder with your own hands should be fastened with screws. In this case, the rear panel must be installed at an inclination of 15° inwards.
The top lid is attached with hinges to make it easy to add food.
After the whole structure is assembled, it is necessary to check whether the compartment opens when the pedal is pressed. If necessary, you can adjust the tension of the bolts.

After making this model with your own hands, you can process it with plaster and an antiseptic. It is not recommended to use varnish or paint, as this can harm the health of chickens.

Bunker model

When forming a bunker model with your own hands, it is important to remember that the design must have a suitable volume. The advantage of such an automatic plastic feeder is that it is easy to clean and easy to operate.

Tools and materials

To make your own hopper feeder, you will need:

plastic containers, while the function of the bunker can be performed by a bucket, bottle or other type of container;
well-sharpened knife;
a plane with a side;
nails, screws and wire.

Step-by-step instruction

First you need to choose a container where the feed mixture will be poured, and the lower part. For the tray, you can take a lid with sides or a container for seedlings. It is important that the bottom diameter is larger than that of the feed bin.
Next, you need to cut holes for each compartment using a knife.
Now the two parts should be fastened with self-tapping screws.
To ensure that the feeder is at the right level, and the chickens are comfortable, you can use nails and wire. If this is not necessary, and the feeder turned out to be quite stable, it can simply be installed on the floor of the chicken coop.

Video "Bunker bird feeder"

In the video (DOM channel), the master demonstrates how to quickly make a bunker-type chicken feeder.

Are you planning to raise chickens and have already built a chicken coop for them? Then it's time to take care of the rest - in particular, the feeder. It is easy to make, especially since you can use various materials. Consider the simplest and most common options for how to make a chicken feeder with your own hands.

A feeder can be made from anything - for example, from boards, boxes, pipes or plastic bottles. But regardless of the material chosen, one problem always appears - we are talking about mixing feed. And if you use several feeders at once, they will take up too much space. There is a way out of this situation, but we will talk about it a little later.

So, in order for the feeder to cope with its functions, it is necessary to prepare for its construction in advance. First, determine the size of the structure and choose a place for it. At the same time, it does not matter whether it will be located in the chicken coop or in the yard - all birds should have free access to it. Moreover, chickens should not crowd or interfere with each other during feeding.

It should also be remembered that chickens need not only dry, but also wet food (we are talking about mixers). In the first case, cylinder-shaped bunkers are excellent, in which the volume of feed is replenished automatically. For wet food, a feeder in the form of a trough is more suitable, on top of which a “turntable” made of timber is installed.

Making a chicken feeder - an overview of popular methods

Of course, the procedure for constructing a trough differs from a bunker-type feeder both in terms of labor costs and the complexity of the work. But modern equipment and materials greatly simplify the process, so there will be no particular difficulties.

Note! When constructing a feeder, one must adhere to one important rule: the design should be stable, food should not spill out of it. Otherwise, there will be not only an overrun of feed, but also a violation of sanitary standards.

Option one. creative cutting board feeder

To make such unusual feeder for birds, you should prepare:

cutting board;
funnel;
a small plastic cup;
rubber hose (transparent);
electric drill.

The further algorithm of actions should look something like this.

Table. Making a cutting board feeder

Steps, no.	Photo	Description
Step 1		Take a funnel (preferably plastic) and circle its outer contours on the board. Try to do everything as accurately as possible.
Step 2		Drill a lot of holes within the drawn circle. It is important not to overdo it here, because the supply of dry food should be limited.
Step 3		Take a pre-prepared transparent hose of the required diameter. Connect the hose to the end of the funnel, if necessary, you can use additional fasteners (for example, a clamp).
Step 4		Take a plastic cup and make a hole at the bottom as shown in the image. The diameter of the hole should be such that the end of the hose fits snugly and holds well.
Step 5		Take the other end of the hose and place it in the hole you made. In case of insufficient density, treat the edges of the hole and the outer surface of the hose with a sealant.
Step 6		Next, you need to glue the socket of the funnel to the cutting board. To do this, process the contour of the circle with holes with sealant.
Step 7		Put a funnel on the circle, hold it in this position until the sealant dries.
Step 8		Connect one end of the hose to the cup and the other end to the glued funnel. The funnel should be at the bottom of the board.

When assembled, the feeder described above will look like this. You can add grain.

Note! The grain will be poured through the hose from the watering can into the cup itself. Also make sure the board is stable, as chickens are more likely to sit on it.

Option two. Bunker feeder from a plastic bucket

This design can be considered automatic, since your participation in feeding the chickens will be minimal. Such a feeder can be purchased ready-made in the store, but it will not be cheap, so you can try to make it yourself. The manufacturing procedure is quite simple.

Of the consumables you will need:

special sectional bowl for animals;
plastic bucket.

Once prepared, follow the instructions below.

Step 1. Take a plastic bucket and make holes in its bottom through which the food will spill out (as shown in the image below).

Step 2 Attach the sectional bowl to the bottom of the bucket using screws.

Step 3 Fill a plastic bucket with grain or any other food, close the lid.

The advantage of this design is that it can be installed in almost any convenient place (put or hang). As the food is consumed, it will automatically pour into the bowl under the influence of its own weight.

Option three. Plastic bottle design

Nowadays, water is often stored in cheap plastic containers. Such bottles are, perhaps, in every home and they can be used to build a convenient feeder.

Step 1. Cut the bottle in half, make holes on the walls in the bottom half, as shown in the image. The size of each hole should be sufficient so that the chicken head freely enters it (it is advisable to leave a small margin).

Step 2 Take the second bottle, cut the bottom in it, then place it upside down inside the prepared incision. As a result, a few centimeters should remain between the neck and the bottom.

Step 3 Pour the grain inside, close the hole in the upper part with something. The disadvantage of this design is that in case of bad weather it must be transferred to the room, however, for placement inside the house, this is the best option.

For chickens, you can make a similar design in smaller sizes using regular plastic bottles. Manufacturing technology will be the same.

Option four. Simple wooden feeder (#1)

If you don’t have a lot of chickens, and only pieces of wood from improvised materials, then you can make the feeder described below. The latter is great for those cases when the owners do not have the opportunity to periodically add grain (in other words, this is also a bunker feeder). It is not difficult to make such a design, the main thing is to clearly follow the instructions below.

First, prepare the following consumables and equipment:

pieces of strong thick plywood or wood;
electric drill, a set of drills;
a pair of loops;
sandpaper;
saw;
screwdriver;
pencil;
roulette.

After that, proceed directly to manufacturing.

Step 1. Start by creating a drawing, then transfer it to the tree, drawing the elements of the required dimensions:

bottom 29x17 centimeters;
two "sidewalls" 40 centimeters high with an upper edge of 24 and a lower edge of 29 centimeters;
two rectangles for the front wall - 28x29 and 70x29 centimeters;
top cover (26x29 centimeters);
back wall (40x29 centimeters).

Step 2 Carefully cut out all the elements.

Step 3 Make holes for the screws in the required places using an electric drill.

Step 4 Sand all surfaces to be smooth and bird-safe.

Step 5 Using screws, assemble all the elements into a single structure. To achieve maximum density, you can use a clamp. It is also important that the back and front walls are attached at a 15° angle.

Step 6 Use the hinges to attach the cover to the back of the side walls.

Step 7. It is also advisable to treat the feeder with an antiseptic. No paint or varnish can be used.

Note! The finished design will turn out to be roomy and comfortable, the food, protected from moisture, will be gradually fed automatically. In addition to labor costs, no other shortcomings have been noticed.

Option five. Simple wooden feeder (#2)

Another simple option is a feeder made in the form of a small trough. It is suitable for those who have a large number of chickens and have a canopy in case of rain.

For work you will need:

thick boards or plywood;
hammer;
screws (you can use nails instead);
saw;
pencil;
paper;
ruler.

Step 1. First, make a drawing of the future design. Extremely accurately determine all the elements, their dimensions and installation locations of fasteners. This is the most important step to avoid possible errors and inconsistencies.

bottom (15x100 centimeters);
a pair of side walls (8x100 centimeters);
one beam (HxWxD - 2x3x100 centimeters);
small end walls with a width of 15 centimeters and a height corresponding to the long side + bottom thickness.

Sawing the end walls is the most difficult step. For a better idea, we advise you to familiarize yourself with the image below.

Step 3 In accordance with the drawn up drawing, cut out each of the elements.

Note! The bottom should be thick and heavy enough so that the birds do not overturn the structure. The height of the walls should be comfortable for chickens.

Step 4 Connect all the elements together. Try not to leave gaps, because food can spill out through them. Additional processing of wood is not required, moreover, if desired, this design can be modified to suit your own needs.

The advantages of such a feeder include durability and strength, as well as versatility with regards to the type of feed used (the latter can be both dry and wet). As for the shortcomings, there is only one - the feeder needs minimal maintenance.

Option six. Two-story wooden feeder

The next option is intended primarily for dry food (although you can use a variety of mixers). Ideal for small spaces, because the second tier compensates for the lack of free space. For work, you will need screws and bars.

Step 1. First, prepare all the elements of the feeder. The main one will be the lower tier, the height of which should be 25, and the width - 26 centimeters. As for the length, it depends on the number of birds.

Step 2 Make special grooves into which the damper will be inserted.

Step 3 The second floor will be a small trough with a board height of 10 centimeters. Install the second floor on the ends of the first, then attach with hinges.

Option seven. PVC pipe construction

An easy-to-implement option that requires minimal cost and effort. PVC pipes are sold everywhere and are inexpensive. To make, use one of the methods below.

Method one. With cutouts

For the construction of this structure, take care of the following consumables:

a pair of PVC pipes (40 and 60 centimeters in length);
two plugs;
connecting knee.

A 60 cm pipe will be installed horizontally and will serve to feed the pizzas. Another pipe is installed vertically and is necessary for the supply of grain. Start by making a hole in a longer pipe, although it is not uncommon to make one large one instead, through which the birds will peck at the grain.

Step 1. On a 60 cm pipe, draw holes with a diameter of 7 cm and with the same pitch.

Step 2 Cut out the marked holes.

Step 3 Put a cap on one end of the pipe.

Step 4 Install a knee on the second end, and, in turn, thread another pipe into it.

Step 5 Fix the resulting structure in the house, preferably in two or three places at once, so that it holds well.

After each falling asleep of grain, put a second plug on top so that debris does not get inside. The described design is also a bunker, so you can add food only once or twice a day.

Method two. With tee

In this case, for manufacturing you will need:

PVC pipes, sized (70, 20 and 10 centimeters);
two plugs;
tee with 45° angle.

Step 1. Take a 20 cm pipe and put a plug on one end. This will be the bottom of the feeder.

Step 2. Put a tee on the other end of this pipe so that the side elbow is directed upwards.

Step 3. Insert a small pipe into the side hole.

Step 4 Insert the pipe of the longest length into the third hole of the tee. Here, as in the previous method, after each feed filling, the pipe must be closed with a plug.

There are other ways to make a PVC pipe bird feeder, as experienced poultry farmers talk about in the video below.

Video - Feeder made of pipe

Option eight. Canister construction

A cheap and easy way to make a feeder.

Prepare for work:

any plastic canister;
a piece of pipe 10-15 centimeters in length;
fasteners;

Step 1. Thoroughly clean and dry the canister.

Step 2. Using a knife or any other tool, cut about 5 holes on the sides. The diameter of the holes should be about 6-7 centimeters so that the head of the chickens fits freely in them.

Step 3. Make a hole in the upper part for filling the grain and attach a pipe on top (the diameters must match). That way the birds won't get in.

To protect against rain and debris, you can additionally take care of a cover for the pipe.

Option nine. CD case construction

Don't throw away your old CD case - you can still use it to feed your chickens!

In order to build such a structure, prepare:

long container;
a large bowl;

Step 1. Clean and dry the container, then cut three or four 2x2 cm holes on its walls near the rim.

Step 2. Fill the container with food, cover with a bowl on top.

Step 3 Turn the container with the bowl over and place it in the required place.

Note! Make sure that there are no sharp corners, about which chickens can get hurt.

Also note that this design is not durable and is designed for a small number of birds.

Option ten. Automatic design

The video below shows another interesting option - a structure that opens under the weight of a chicken.

Video - Automatic feeder

This is not a complete list of possible options - the article describes only the most popular of them. Having shown ingenuity and imagination, you can come up with your own design, the main thing is that the product is durable and safe for feathered pets.

How often have you thought about automating the process of feeding chickens? You could save a lot of time and effort, and at the same time the chickens were full and happy. If you have everything you need and desire, a do-it-yourself automatic chicken feeder will pay off very quickly. What is needed for this - you will find out further.

What is an automatic feeder?

Automatic feeders are different, but they all have the same principle of operation. They help automate the supply of pet food. Feed is replenished exactly as much as was eaten, while the rest of the feed is stored in the closed part of the feeder. This will protect your pets from overeating or scattering food, from feathered thieves and the vagaries of the weather (rainfall, snow and wind). The benefits are visible to the naked eye - automatic feeders not only help to save and dose feed, but also allow you to go away for long term without fear that the animals will suffer from starvation.

The automatic feeder for chickens is designed only for dry type of karma, such as compound feed or grain.
Auto feeders can be made by hand from different materials: wood, plastic, plywood, steel, etc. There are more complex designs and with additional features, such as a dispenser.

We make an automatic feeder with a dispenser

This model was invented by Australian farmer John Riddell. It is designed for a small number of chickens, up to 20. You can design several with your own hands, it will be more convenient for your pet birds, especially if there are several more. Its peculiarity lies in the fact that access to the feed is opened only when the chicken approaches the feeder and steps on the pedal. Only then, under its weight, the lid of the compartment with food opens.

Tools and materials

You will need:

plywood sheet;
wooden bars;
furniture bolts;
2 loops;
saw;
drill.

Step-by-step instruction

The main instruction will be contained in the video. There are no strict parameters as such. You can make it narrower, wider, taller, or whatever you like. The main thing is to first draw all the details so that all sizes fit together (all walls of the same height, length, and so on).

First, draw 10 parts on a plywood sheet: a feed cover, 2 side walls, a bottom, a back wall that should be mounted at an angle, 3 front bars, a cover over the grain, a wide pedal.
From the bars you need to make 6 parts. 2 should be the longest for attaching to the pedal, 2 should be a little shorter for the cover above the feed and the last 2 are the shortest for fastening the 2 previous ones together.
All walls of the feeder must be fastened together with screws. Make sure that the back panel is angled into the structure by about 15 degrees. For greater density it is advisable to use a clamp, if available.
To secure the top cover, use 2 loops, so that later you can always fold it back and conveniently refill the food.
The most intricate part with the bars - the photo above shows approximately in what form everything should be mounted. The first bars must first be attached from the sides to the lid of the compartment with food, and at their opposite end, make 2 holes with your own hands. One of them should be somewhat wider than the bolt itself and located closer to the end of the bar. It should correspond to the same hole in each side wall of the feeder. Then we screw the bolt so that it not only fixes the bar on the wall, but also allows it to turn.

We attach the longest bar according to the same principle with our own hands to the pedal of the automatic feeder, and the hole for fastening to the wall and turnover must be made approximately at a distance of 1/5 of the entire length at the free end of the part. At the very end, we will make a second hole.
We use the remaining free holes in order to combine the structure with the third, smallest bar. The connection must be strong and static. Make sure that when you press the pedal of the automatic feeder, the lid of the feed compartment rises. If this does not happen, adjust the tension of the bolts.
If you wish, you can process the finished structure with your own hands, first with sandpaper, for smoothness, and then with antiseptics. You should not cover with varnish and paint, as they can harm the birds, and the feeder will last for many years anyway.