For many hundreds of years, Europeans considered precious stones to be the main values ​​of India. But in fact, its main wealth has always been iron. Indian steel was highly valued back in the time of Alexander the Great and was used to produce the highest quality and most expensive weapons.

Bukhara and Damascus were famous centers of arms production in the medieval East, but... they got the metal for it from India. It was the ancient Indians who mastered the secret of the production of damask steel, known in Europe as Damascus. And they also managed to tame and use elephants in battles, and in the same way as their horses, they dressed them in armor made of chain mail and metal plates!

India produced several grades of steel of varying quality. Steel was used to manufacture various types of weapons, which were then exported not only to the markets of the East, but also to Europe. Many types of weapons were unique to this country and were not used anywhere else besides it. If they were bought, they were considered as a curiosity.

Very dangerous in skillful hands was the chakra - a flat throwing disc, used in India until the middle of the 19th century. The outer edge of the disk was razor-sharp, and its edges inner hole- stupid. When throwing, the chakra was intensively spun around the index finger and thrown at the target with all its might. After that, the chakra flew with such force that at a distance of 20–30 m it could cut a green bamboo trunk 2 cm thick. Sikh warriors wore several chakras on their turbans at once, which, in addition, protected them from above from a saber strike. Damascus chakras were often decorated with a gold notch and religious inscriptions were made on them.

In addition to ordinary daggers, the Indians very widely used katar - a dagger with a handle perpendicular to its longitudinal axis. Above and below, she had two parallel plates, ensuring the correct position of the weapon and at the same time protecting the hand from someone else's blow. Sometimes a third wide plate was also used, which covered the back of the hand. The handle was held in a fist, and the blade was like an extension of the hand, so that the blow here was directed by the stronger muscles of the forearm, and not the wrist. It turned out that the blade was an extension of the hand itself, thanks to which they could strike from various provisions, not only standing, but even lying prone. Kathars had both two and three blades (the latter could stick out in different directions!), have sliding and curved blades - for every taste!

Madou. A very original weapon was a pair of antelope horns, which had steel tips and were connected on one handle along with a guard to protect the hand, with points in different directions.

Nepal was the birthplace of the specific shape of the kukri knife. It was originally used to cut its way through the jungle, but then found its way into the arsenal of the Nepalese Gurkha warriors.

Not far from India, on the island of Java, another original blade was born - kris. It is believed that the first kris were made in Java by a legendary warrior named Juan Tuaha back in the 14th century. Later, when the Muslims invaded Java and began to stubbornly spread Islam there, they also became acquainted with this weapon. Appreciating these unusual daggers, the invaders began to use them themselves.

The blades of the first kris were short (15–25 cm), straight and thin, and entirely made of meteoric iron. Subsequently, they were somewhat lengthened and made wavy (flame-shaped), which facilitated the penetration of weapons between the bones and tendons. The number of waves varied (from 3 to 25) but was always odd. Each set of convolutions had its own meaning, for example, three waves implied fire, five were associated with the five elements, and the absence of bends expressed the idea of ​​unity and concentration of spiritual energy.

The blade, made of an alloy of iron and meteoric nickel, consisted of several repeatedly forged layers of steel. Of particular value to the weapon was the moire-like pattern on its surface (pamor), formed during the treatment of the item with vegetable acids, so that the grains of stable nickel stood out clearly against the background of deeply etched iron.

The double-edged blade had a sharp asymmetric extension near the guard (ganja), often decorated with a carved ornament or a patterned notch. The handle of the kris was made of wood, horn, ivory, silver or gold and was carved, with a more or less sharp bend at the end. characteristic feature kris was that the handle was not fixed and easily turned on the shank.

When capturing the weapon, the bend of the handle was placed on the little finger side of the palm, and the upper part of the guard covered the root of the index finger, the tip of which, together with the tip of the thumb, squeezed the base of the blade near the bottom of the ganja. The tactic of using the kris involved a quick thrust and pull. As for the "poisoned" krises, they were prepared quite simply. They took dried dope seeds, opium, mercury and white arsenic, thoroughly mixed everything and crushed it in a mortar, after which the blade was covered with this composition.

Gradually, the length of the kris began to reach 100 cm, so that in fact it was no longer a dagger, but a sword. Altogether in South-East Asia up to the present time, there are more than 100 varieties of this type of weapon.

Kora, Khora or Hora is a heavy striking sword from Nepal and northern India, used for both combat and ritual purposes. Combat and ritual kora are very similar, only the sacrificial sword is wider and heavier. It has a very heavy expanded pommel, as it must add weight to the blade and decapitate the sacrificed animal with a single blow. The bark blade has a characteristic "duck's foot" profile, thin near the handle, with a slightly curved blade widening towards the point. The massive blade has a curved shape, sharpened on inside. Sometimes a fuller is used in the form of a wide groove located along the entire length of the blade and replacing the rib. The presence of several faces allows you to strike with different parts of the sword. The total length of the sword is 60-65 cm, the length of the blade is 50 cm. The guard is ring-shaped, made of metal and has the shape of a disk. Often the guard is placed both on the side of the blade and on the side of the pommel, and protects the hand from both sides.
The bark is usually adorned with an eye symbol or other Buddhist symbolism that is placed on each side of the blade. Sheath made of genuine leather. There are two types of sheaths for the kor: the sheath adapted to the shape of the sword, unfastened by means of buttons located along the entire length of the scabbard. In another version, a large sheath looks like a carrying case. There is a bark model with a longer and lighter blade.

Sword puttah bemoh
A two-handed sword or epee with a long, narrow, straight blade and two hilts separated by guards in the form of crosses or cups. It was first mentioned in the treatises of the 16th century "Nihang-nama" and "Nujum al-Ulum". Several copies of such swords have been preserved. One of them has a total length of 165 cm and a blade length of 118 cm. The handle is divided into two parts, each of which is equipped with a cup-shaped guard. The blade is quite narrow, similar to a sword blade.
It is believed that these swords originated in the 16th century, possibly under the influence of the German zweichanders, and were later supplanted by the Khanda weapons. However, the mel puttah bemoh has an important difference from the European two-handers - a narrow and relatively light blade, which was not so effective for chopping.



In general, the edged weapons of India and the lands close to it were extremely diverse. Like many other peoples of Eurasia, national weapon Hindus was a straight sword - handa. But they also used their own types of sabers, which were distinguished by a relatively small curvature of the wide blade, starting from the very base of the blade. Excellent masters of forging, the Indians could make blades that had a slot on the blade, and pearls were inserted into it, which rolled freely in it and did not fall out! One can imagine the impression that they made, rolling into the slots, on an almost black blade made of Indian damask steel. No less rich and pretentious were the hilts of Indian sabers. Moreover, unlike the Turkish and Persian ones, they had a bowl-shaped guard to protect the hand. Interestingly, the presence of a guard was also characteristic of other types of Indian weapons, including even such traditional ones as a mace and a mace.

Talwar is an Indian saber. Appearance talwara is typical for sabers - the blade is of medium width, somewhat curved, sharpening can be one and a half, but this is not necessary. There are variants of talwar both with and without yelman. A dol may be on a talwar blade, but most often it is not there. In some cases, the dol can be generally through, sometimes movable balls of various materials are inserted into it.
The main difference between the talwar and other sabers is, first of all, its disc-shaped pommel. Also, this saber necessarily has a “ricasso” (heel), even if it is small in size. The length of the blade can be from 60 to 100 cm, width - from 3 to 5 cm. The handle of the talwar is straight, with a thickening in the middle, and is designed exclusively for one hand. The disc-shaped pommel prevents the weapon from being lost and gives this saber a unique look. It is often richly decorated, as are the hilt and guard. The latter can have both a straight shape and an S-shaped or D-shaped.
Ornaments decorating the talwar usually contain geometric figures, images of animals and birds. On the weapons of the rich, you can see the inlay with precious stones or enamel.

Talwar has been known since the 13th century and was a very popular weapon in northern India. Especially among the Rajputs, members of the Kshatriya caste, who used this weapon right up to the 19th century.
In addition to the military, the talwar also has a certain sacred purpose. According to mythology, he is one of the ten weapons of the gods, with the help of which the forces of good fought against demons and other evil.

Pata or puddha is an Indian sword with a long, straight, double-edged blade that is connected to a gauntlet - a steel guard that protects the arm up to the elbow.

Pata is a combination of a straight double-edged sword and armor protection of the forearm and hand. The blade fits into a protective cup with a handle inside. The pat has a handle perpendicular to the blade, just like a katar, but there are several belts on the armor to fix the hand.
Pata blades were from 60 to 100 cm with a width at the handle of 35-50 mm. Weight reached 1.5 - 2.2 kg. The stalemate blade was fastened with rivets to the plates extending from the protective cup.
The cup of pat covering the brush was often made in the form of an elephant, snake, fish or dragon head. In this case, the blade protruded from the open mouth like a huge tongue. Another popular cup-shaped motif is the mythical Yali lion swallowing an elephant.

Apparently, the pata developed at one time from the katar (Indian dagger), having undergone several modifications of the guard and hypertrophied. First, a protective plate covering the wrist was added to the catarrh, then it was connected to the side metal strips. This design gradually transformed into a “plate glove” that covered the arm to the elbow. The "glove-handle" could be of a skeletal type - from metal crossed strips (probably earlier forms) or made in the form of heads of mythical animals.
According to another version, on the contrary, at first there was a stalemate, from which cathars originated by simplifying the design. But the truth is that both katar and pata were in service in the same period of history.

Bhuj (also kutti, gandasa) is an Indian glaive-type weapon. It consists of a short handle (about 50 cm) connected to a massive blade in the form of a knife or cleaver. Thus, this weapon is similar to the short variants of the palm tree or dadao.
In the classic version, the bhuja blade was quite wide and had one and a half sharpening, while it was distinguished by a double bend: closer to the handle it was concave, and towards the tip it was curved, so that the tip was directed upward relative to the handle. In the center of the blade from the tip to the level at which the butt began, there was a stiffening rib. The handle was made more often from metal (steel, bronze, copper), less often from wood. In some cases, a scabbard, usually made of wood and covered with velvet, relied on the bhuj.
Thanks to the massive blade, this weapon could deliver powerful chopping blows, so one of its names meant "knife-axe". In addition, the junction of the blade with the hilt was sometimes made in the form of a decorative elephant's head, from which another name comes - "elephant knife".

The name "bhuj" is derived from the city of the same name in Gujarat, where this weapon comes from. It was widespread throughout India, especially in the north. There were also rarer options, for example, those that had a handle with a guard, or differed in a different blade shape. Bhuj is also known, combined with a primer pistol, the barrel of which is located above the butt of the blade; a stylet is inserted into the end of the handle opposite to the blade. IN south india an analogue of bhuja was used - vertchevoral, which was distinguished by a concave blade and was used to cut through thickets.

Driven - a slander used in India in the 16th - 19th centuries.
Its name comes from the Persian word meaning "crow's beak", since this form had warhead drove. The beak was made of steel in the form of a rather thin dagger blade, usually with a stiffening rib or fullers. The point was sometimes bent down to the handle, in other cases the blade was straight. On the butt, there was sometimes a decorative bronze figurine depicting, for example, an elephant. Less often, a small ax was made instead of it - such a weapon was called tabar-driven.

Coins of other types were less common. In particular, klevtsy with a round cross-section or a faceted beak were in circulation. Quite exotic artifacts have also been preserved, one of which has 8 beaks at once, fixed in such a way that 2 were directed to each of the four sides, and blades of axes are attached between them. Another specimen is similar to a tonga ax with a double point pointing forward.
The hilt of the chasers was made of wood and metal. Sometimes a stylet could be inserted into the hollow metal handle from the opposite side of the warhead. These coinage were one-handed weapons. Their total length ranged from 40 to 100 cm.

Haladi dagger.
Haladi had two double-edged blades connected by a handle. It was an offensive weapon, although the slightly curved blade could easily be used to parry. Some types of haladi were made of metal and worn like brass knuckles, where another spike or blade could be located. These types of haladi were perhaps the world's first three-bladed daggers.

Urumi (lit. - twisted blade) - a traditional sword common in India in the northern part of Malabar. It is a long (usually about 1.5 m) strip of extremely flexible steel attached to a wooden handle. The excellent flexibility of the blade made it possible to wear the urumi discreetly under clothing, wrapping it around the body.

In some cases, the length of such a sword could reach six meters, although one and a half meters can be considered the standard. Previously, such flexible swords were worn by assassins, remaining unnoticed for weapons. After all, this sword, as already mentioned, is very flexible, and it can be wrapped around the belt.
A flexible sword is a rather dangerous weapon that requires martial arts. It can work both as a regular whip and as a sword. Interestingly, the urumi can have more than one stripe, but several, which makes it a powerful and very dangerous weapon in the hands of a true master.
Wielding this sword required good skill. Due to the fact that the urumi was very flexible, there was a serious risk of self-harm for the wearer. Therefore, beginners began training with long pieces of fabric. Ownership of urumi is included in the complex of traditional South Indian martial art kalaripayattu.

Kalaripayattu, as a martial art, developed in the second half of the 16th century, despite the prohibitions of the British colonialists, who feared the emergence of an uncontrolled fighting structure. But despite the bans, schools continued to train Kalaripayattu fighters. The paramount rule of martial art for a warrior was perfect control of his body. The battle took place in conditions of incessant movement, instant attacks and evasions, jumps, flips and somersaults in the air.
The Kalaripayattu fighter was armed with a saber or dagger, a trident or a pike with a steel tip. Some masterfully wielded a long double-edged sword. But the most terrible weapon was the urumi sword. From the handle extended several flexible blades, sharp as a razor, about two meters long. The duel could end in the first second, because the movement of the urumi was completely unpredictable. One swing of the sword carried the blades apart and their further movement was unpredictable, especially for the enemy.

The elaborate oriental bow was also well known in India. But due to the peculiarities of the Indian climate - very humid and hot - such a bow was not widely used. Having excellent damask steel, the Indians made small bows from it, suitable for horsemen, and bows for infantrymen were made of bamboo in the manner of solid wood bows of English shooters. Indian infantry of the 16th-17th centuries. already quite widely used long-barreled matchlock muskets equipped with bipods for ease of shooting, but they were constantly in short supply, since they were produced in handicraft production in in large numbers it was extremely difficult.

A feature of Indian percussion weapons was the presence of guards even on six-pointers and maces.

Very curious were Indian chain mail with a set of steel plates in front and behind, as well as helmets, which in India in the 16th-18th centuries. they were often made from separate segmental plates connected by chain mail weaving. Chain mail, judging by the miniatures that have come down to us, were both long and short sleeves to the elbow. In this case, they were very often supplemented with bracers and elbow pads, often covering the entire hand.



Equestrian warriors often wore elegant bright robes over chain mail, many of which had gilded steel disks on their chests as additional protection. Knee pads, gaiters and greaves (mail or in the form of solid forged metal plates) were used to protect the legs. However, in India, metal protective shoes (as in other countries of the East), unlike the protective shoes of European knights, have not received distribution.



Indian shield (dhal) from Rajasthan, 18th century. Made of rhinoceros skin and decorated with rock crystal umbos.

It turns out that in India, as well as in all other places, until the very 18th century, the armament of heavily armed cavalry was purely knightly, although again not as heavy as it was in Europe until the 16th century. Horse armor was also widely used here, or at least cloth blankets, which in this case were supplemented by a metal mask.

Kichin horse shells were usually made of leather and covered with fabric, or they were lamellar or lamenar shells made of metal plates. As for horse armor, in India, despite the heat, they were popular until the 17th century. In any case, from the memoirs of Afanasy Nikitin and some other travelers, one can understand that they saw the cavalry there "entirely dressed in armor", and the horse masks on the horses were trimmed with silver, and "for the majority they were gilded", and the blankets were sewn from multi-colored silk, velveteen, satin and "fabrics from Damascus".


Bamboo armor for war elephant, India, 1600

This is the most famous war elephant armor. It is on display at the Royal Armory in Leeds, England. It was made around 1600, and it came to the shores of Foggy Albion 200 years later.
Elephants fought in this armor on the territory North India, Pakistan and Afghanistan. Today it is the largest elephant armor in the world, which is officially registered in the Guinness Book of Records.


Scale armor for a war elephant, India, 17-18 centuries

Metal plates are sewn onto some kind of base, such as leather. Some of the plates are made of yellow metal, like roof tiles. Each plate overlaps several adjacent ones, which allows you to get stronger protection, and make the plates thinner. Thanks to thinner and lighter plates, the weight of the entire armor is also reduced.


War Elephant Plate Armor

Talwar (Hindi: तलवार; Urdu: تلوار, Pashto, Punjabi: ਤਲਵਾਰ) is a type of saber with a small or moderate blade bend, common in the Indian subcontinent, modern India, Pakistan, Bangladesh, Nepal and Afghanistan. The terms talwaar and tulwar were used as a definition of weapons.

Story

Talwar appeared along with other curved swords: Arabic saif, Persian shamshir, Turkish klich (kilich) and Afghan saber. All of the listed types of weapons were descendants of ancient curved swords made in the territory of Turkic Asia. As a rule, the talwar blade did not have such curvature as that of the shamshir. The saber was distinguished from the standard kilich by the small width of the blade. Talwar was widely used by the Great Mughals, who were of Turkic-Mongolian origin.

Characteristics

There were a great many varieties of talwar, they were distinguished by the type of blade. There were also very non-standard ones: from double-edged blades (zulfikar) to very massive options (sometimes they are called tegha - executioner's swords). However, all blades were united by a curved shape, and the vast majority of talwars were similar to a typical saber.

In many instances of the talwar, the largest radius of curvature was located in the distal half of the blade, exceeding the radius near the handle. Also, a fairly common design feature of the saber was the expansion of the blade at the tip (without the expansion on the reverse side of the butt, characteristic of the tusk).

The profile of the blade of the saber of the British light cavalry of 1796 is similar to the talwar, and among experts there is an opinion that it was the talwar that was the progenitor of the British saber.

Despite the influence of Middle Eastern swords on the design of the saber, the standard talwar was characterized by a wide blade, which distinguished it from the shamshir. Later copies of the weapon were equipped with European-made blades mounted in Indian handles. The hilt of a standard talwar was called the “disc-shaped hilt”, due to the presence of a disc-shaped flange on the pommel. Often there was a small protrusion in the center of the pommel, through which a cord was threaded to secure the sword to the wrist. The saber hilt included a simple guard, which often had a shackle to protect the hand. As a rule, it was made of iron, while specimens of brass and silver were found. The blade was fastened with adhesive resin. Expensive weapons were depicted with silver or gilt decorations in a form called "koftigari".

Application

The talwar was used by both cavalry and infantry. For chopping blows, by analogy with a saber, the handle of the weapon was tightly compressed in the hand, while the pommel rested on the wrist. The features of the talwar protected the hand and improved control over the weapon, allowing for effective slashing and cutting blows. Because the saber blade, unlike the shamshir, did not have a large curvature, the weapon was also used for stabbing. The blades of some specimens of the talwar expanded at the point, which allowed skilled warriors to cut off limbs or even decapitate the enemy. In case he was on close range, a spike located on the pommel made it possible to deliver a stabbing blow. The grip of the talwar could be carried out with the index finger grasping the guard of the saber.

cultural significance

The weapon is still used today in the Shia rite of self-flagellation in memory of Hussein ibn Ali. Today, the term "talwar" has the literal meaning of "sword"/"dagger" in most languages ​​of the Indian subcontinent.

Talwar - Saber against demons

Talwar became a symbol of valor of the warrior caste of India

The weapons of the Indian gods impress with their exoticism and destructive power. Here is the mysterious, lightning-like vajra, with which Indra threw down his enemies.

And chakra, Vishnu's throwing disc, which only masters could use. It is all the more surprising to see in this series a simple and concise saber - talwar.

It is customary to say that the beauty of a weapon lies in its effectiveness and the absence of unnecessary elements. This is fully applicable to the talwar, the traditional saber of Indian warriors. Moderately curved blade, comfortable handle, perfect balance. Only the unusual looking hilt attracts attention. These weapons have been used for centuries by both foot and horsemen. And not only in India, but also in Pakistan, Bangladesh, Afghanistan and even Nepal.

The secret of the hilt

Talwar appeared around the 13th century and belongs to a large family of oriental weapons, which originated from the ancient curved swords with which the Turkic tribes conquered Asia. The closest "relatives" of the Indian talwar are the Arabic saif, Persian shamshir and Turkish kilich. It is distinguished by a relatively small and smooth bend, as well as a small width of the blade.

However, as is often the case, the word "talwar" in India is often used to refer to any bladed weapon. Therefore, there are talwars of very unconventional forms. Some of them even refer to the so-called zul-fiqars - curved swords, the blade of which is bifurcated at the end. According to legend, the prophet Muhammad owned such a sword.

However, there is a feature by which talwar can be unmistakably recognized and distinguished. This is the shape of the hilt. The straight handle with a noticeable thickening in the middle was crowned with a large disk, on which the fighter's hand seemed to rest. Such a system, on the one hand, limited the freedom of movement of the hand, preventing the sword from swinging freely and performing complex feints. But on the other hand, it increased control over the blade and strengthened the blow.

The hilts of the talwars were often equipped with a shackle to protect the fingers.

But she was never a mandatory element and could acquire the most different forms. The traditional material for making the hilt was iron, sometimes brass and silver.

Another feature is the position of the hilt relative to the blade. In North Indian talwars, the hilt was simply placed in line with the blade, which made it easier to stab. In the south, the handle was tilted. This small angle increased the chopping blow and allowed the saber to be drawn a little further during cutting and cutting movements.

insidious strike

The variety of forms also touched the blade. Almost all of them have a length within 100 centimeters, but they can vary greatly in width. As a rule, the talwar blade adorns one or more dols.

by the most original decoration, which only the most expensive copies made for representatives of the highest nobility have, was the so-called mochi-dawati. This is a through groove that ran along the blade. Several freely rolling metal balls were placed in it. And sometimes they were not balls, but pearls! Contrary to numerous legends, such decoration was purely decorative and rather reduced fighting qualities saber, which gave it some special lethality. Talwars with mochi-dawati were more often worn with full dress than taken into battle.

There are no strict rules for sharpening a talwar. Most often, the blade was only on one side of the blade, but one and a half sharpening was also common. Often there is an extension in the last third of the blade - elman - to enhance the chopping blow.

The shape of the talwar allowed it to be used by both horsemen and foot soldiers. Receptions at the same time could be very diverse. With the same efficiency, it was possible to chop, cut and prick with the same efficiency, which favorably distinguished it from most competing weapons. It is known that skilled fighters could inflict blows of such terrible force with relatively light talwars that they chopped off a limb or even the head of an opponent.

A completely unique technique, which was owned only by the best masters, there was a blow at an extremely close distance, delivered by a long spike located on the very disk crowning the hilt. However, not all talwars had such a spike. Very often there was just a small ledge with a through hole, into which a lanyard was threaded, worn on the wrist.

FOR EUROPEANS

In 1796, a new type of saber was put into service with the British light cavalry. The initiator of its development was Captain John Le Marchant, who noticed that before that, standard army sabers were too long and heavy. The new blade was much lighter, had a stronger curve and a pronounced point. In his notes, Captain Marchand noted that he considers the sabers of the Turks, Mamluks, Hungarians and Moroccans to be the best cavalry melee weapons. However, according to many weapons experts, he took the Indian talwar as a model for the new army saber. It is known that this similarity was noted by the Indians themselves. Some Indian gunsmiths even converted the English sabers that got to them into real talwars, replacing the European hilt with a traditional one with a flat pommel. It was with sabers of the 1796 model that the English cavalry went through all the battles of the Napoleonic Wars.

The best of the best

Most of all, the talwar was glorified by the Indian Rajputs. This is not only a people, but at the same time a caste of Kshatriya warriors. Since the 9th century, they have played a huge role in both domestic and foreign policy. The Rajputs, who put honor and military prowess above all, more than once claimed to unite the disparate Indian states under their rule. However, they managed to gain a foothold only in the northwest. This territory was called - Raj-putana. Currently, there is the largest Indian state - Rajasthan, with its capital in Jaipur.

The Rajputs, who sacredly kept the faith of their ancestors, became a serious problem for the Islamic conquerors who invaded India in the 11th century. The Rajputs fought endless and sometimes very successful wars against the Delhi Sultanate. Their military skill and complete contempt for danger inspired respect and fear in the enemies. In a hopeless situation, the Rajputs never surrendered, but fought until last drop blood. Or they committed collective suicide along with their wives and children.

Most likely, it was at this time that the talwar began to be depicted as one of the attributes of the Hindu gods. After all, it was the talwar who was a true friend and companion of the main defenders of Hinduism for centuries.

However, the valor of the Rajputs still could not prevent the conquest of India by the troops of Babur, who founded the Mughal empire here. The Rajputs were forced to recognize the authority of the Muslim rulers, but retained the right to autonomy. And they continued to resolutely resist any attempts at Islamization, raising uprising after uprising.

The unwavering steadfastness of the Rajputs is legendary. And their legendary weapon became a symbol of martial spirit and art. Muslims also valued talwars extremely highly, moreover, it was this saber that began to be used in rituals by representatives of one of the main branches of the UROK My world

Authenticity Guaranteed: Seller's Warranty

Type of weapon: Saber


Talwar, talwar, tulwar (talwar) - cold bladed weapons, Indian saber. This weapon appeared around the 13th century or a little later and was used until the 19th century. Talwar was most common during the Mughal era in Northern India, and was also a popular weapon among the Rajputs (the people of the Punjabi group living in India and Pakistan).
- IN military history India "Talwar" is the most general term for the definition of the word "sword". According to ancient Indian literature, the Talwar is one of the ten weapons of the gods. According to the legends, the gods, personifying Good, used these tools in the fight against demons, personifying Evil.
- Blade forged patterned steel, pronounced curvature. A clear beautiful pattern can be traced along the entire length of the blade.
- There are traces of forging on the butt, typical for the manufacture of Indian blades.
- Ephesus talwara deserves special attention. It consists of a handle made together with a crosshair and a pommel.
- The handle is steel, expanded in the middle part.
- The handle goes into a crosshair and ends with a disc-shaped pommel with a ledge.
- Cross handle with straight ends, ending on the sides with decorative, three-part extensions and flat guides in the center of the blade.
- A protective s-shaped bow extends from the end of the cross.
- Wooden scabbard, covered with leather (old, not restored).
- It is an antique item, a weapon of historical and cultural value.
*GENUINE ORIENTAL MILITARY WEAPONS MADE BY REAL MASTERS OF THE PAST*
*FOR COLLECTORS AND CONSISTS OF EFFECTIVE ORIENTAL WEAPONS*
- talwar length 86 cm.
- blade length 74 cm.
- blade width 33 mm.
- butt width 8 mm.

*DEAR AUCTION PARTICIPANTS, A HUGE REQUEST TO YOU, DO NOT MAKE RASHING BIDS, BE CAREFUL AND FOLLOW ALL THE CONDITIONS STATED BELOW*

*Questions related to the lot you are interested in, ask before the end of the auction.*
*The buyer who wins the lot, FIRST gets in touch WITHIN 2 DAYS.*
*CONFIDENTLY REQUEST the winners of the auctions to write in the subject line of their messages the name and number of the lot.*
* PAYMENT for the lot: SB card 5469 **** **** 8913 WITHIN 4 DAYS.*
*ATTENTION!!! The recipient of payments is always EFREMOV SERGEY VYACHESLAVOVICH *
*Lot is sent: by KIT transport company or DPD courier service.*
*Lot forwarding is carried out at the expense of the recipient.*
*I DO NOT BE RESPONSIBLE FOR THE WORK OF TRANSPORT COMPANIES.*
*The quality of packaging and the speed of dispatch I GUARANTEE.*
*By feedback, I confirm receipt of payment and dispatch of the lot, I provide the departure number.*
* I make shipments only within the Russian Federation *

Blade weapons of the Indo-Iranian region. Sabers

But not only with straight and curved swords, some of which we have already examined in the previous article, Hindustan is famous.

Beginning with the Muslim invasions, swords are increasingly being replaced by light sabers. Western researchers determine the type of saber (and some swords) by the shape of the hilt.

This view does not appear to be entirely correct. It is necessary to consider the object as a whole - the handle and the blade. In some cases, a double name is possible. But more on that later. And now let's start our acquaintance with the sabers of the Indo-Iranian region.

Talwar, or "tulwar" (tulwar), is the most common saber in the Indo-Iranian region, which can be considered typically Indian. According to ancient Indian literature, the talwar was considered one of the ten instruments of the gods. The blade is flat or lenticular in cross section, often one and a half sharpened, slightly or moderately curved, of medium width, always with a ricasso - that is, its cutting edge of the blade begins 5-7 cm from the handle, and behind the crosshair there is a small unsharpened "platform". In later talwars, the blade has a pronounced expansion at the tip - elman. The blade can be both with valleys and without them. Sometimes the dol was made through, and a number of metal balls or even pearls were placed there, which rolled freely. With the advent of Europeans in the region, combat blades from Europe began to be actively used, in which the handle was simply replaced with a talvar. Ephesus talwara deserves special attention. The cheren is barrel-shaped, with a thickening in the center, the pommel is disc-shaped, slightly inclined, with a domed protrusion in the middle, the crosspiece is straight, short, with widened ends. Often there is an s-shaped bow. But there is also a d-shaped one. The scabbard was made of wood and covered with velvet or leather. On the scabbards of "rich" talwars, the mouth and tip were made of metal. The length of the talwar is 90-120 cm.

A talwar with a very wide blade is called a tega, or tegha (tega). It is not often met, and it is considered to be an executioner's tool, although Egerton writes that it was military weapon. In general, talwars were very common among warriors of different incomes. It could be a simple weapon of a warrior, or a richly decorated blade of a raja.

No less common was a saber of Iranian origin - shamshir, or "shamsher" (shamshir), - "lion's claw". The blade of this saber is narrow, but thick, usually longer than that of the talwar, has a large curvature, which allows you to deliver the most effective blows when cutting. In cross section, it is lenticular or flat. Ricasso and elmani - no. The handle is simple, with a slight bend under the little finger, directed towards the blade, allowing you to better hold the saber. It consists of two bone or, more rarely, horn overlays-cheeks riveted to the shank. From below, the cheeks are additionally fixed with a steel cap, and from above, with a steel simple straight crosshair with small elegant splints (metal plates that reinforce the blade in the guard area), which give strength to the weapon in the most loaded place. In richly decorated shamshirs, the crosshair, cap and metal parts of the scabbard could be made of precious metals, decorated with niello, enamel, notch or stones. The scabbard of the shamshir is curved in such a way that it allows the blade to be removed without the slit that is found on the scabbards of Turkish curved sabers. The scabbard was made of wood and covered with leather, which was often embossed or embroidered with silk thread. The tip of the scabbard could be metal, but more often it was made of leather or was completely absent. But two clips were obligatory, for which the shamshir was hung on the belt.

In general, it should be noted that the Indians sought to acquire richly decorated Persian-made shamshirs with damask steel blades, which were considered a status thing. The head of an animal was often depicted on the hilt (for example, a cap was made in the form of it). At the same time, many now believe that according to Muslim customs, the image of people and animals was forbidden anywhere, and this could only be done in a stylized way, for export to another country and for very expensive copies. Allegedly, violation of this rule was considered religious sacrilege and threatened with loss of one's head. And shamshira with the image of animals on the handle are made exclusively for India. In fact, all this is not entirely true. Muslims are divided into two branches: Sunnis and Shiites. Sunnis are indeed forbidden to depict people and animals, therefore, for example, on Turkish weapons we will see only floral ornaments, sayings from the Koran and signatures of craftsmen and weapon owners. But the Shiites, which include the Persians, left us a lot of magnificent miniatures on silk and paper, as well as images of people and animals on armor and weapons. So, for example, the “torn scenes” carefully worked out on the blades, when an eagle kills a swan or a leopard an antelope, and images of people on the handles are quite typical of Iranian weapons. And on the Persian shields, in general, you can see household, hunting, and battle scenes. These same miniatures reveal a curious fact to us. It turns out that shamshir and talwar were widely used for hunting. The rider pursued the game (and it could be both ungulates and predators) and chopped it with a saber.

V.V. Vereshchagin. Warrior Rider in Jaipur (1881).

But back to the use of shamshir. It is definitely a rider's weapon. Its curved shape is dictated by functionality, the desire to expand the capabilities of the blade when striking from above when attacking enemy foot soldiers. Some authors believe that shamshir is ideally suited for warfare on horseback and in the ranks shoulder to shoulder. Although the latter is debatable. But what is important to note is that the best shamshirs, the blades of which are forged from damask steel, are only suitable for combat with an enemy not protected by chain mail or armor. It is impossible to cut chain mail with damask shamshir, and even more so plate armor. Damascus shamshir is very sharp, but also very fragile. It is powerless against armor. But cutting down enemy soldiers unprotected by armor is another matter, especially if they are running. By the way, when they talk about the properties of damask shamshir, I remember famous story about how Richard the Lionheart and Sultan Saladin argued about whose blade is better - an English sword or an Eastern saber? Richard, according to legend, cut down with heavy knight's sword iron bar, leaving no notches on the blade. Saladin drew a damask saber, turned the blade up and tossed up the handkerchief. The handkerchief, touching the blade, was cut into two halves. What kind of saber was in the hands of Saladin - history is silent. But it is quite probable that it was also shamshir.

Returning to the problems of the name of the sabers, which I mentioned earlier, it must be said that the shamshir blade was often placed on a talvar handle. Many English-speaking authors call such a saber a talwar. In my opinion, it is more correct to say shamshir with a talwar handle or talwar with a shamshir blade. This defines the subject more precisely.

Separately, I would like to consider a blade typical of Sri Lanka, formerly called Ceylon. This island is inhabited mainly by the Sinhalese. Sinhalese are Indo-Aryans, usually of medium height, "small-boned", with Caucasoid features and dark skin. The saber (sword), as in many other cultures, was an important symbol of royal power for the Sinhalese. In the texts describing the reign of Vijayabahu IV (second half of the 13th century), it is mentioned that the swords constitute the wealth of the king, however, along with other treasures. The Europeans who colonized the island in the 16th century (first the Portuguese, then the Dutch, and at the end of the 18th century the British) noted an increased attention to weapons, especially at the royal court. They wrote that noble people wear a short sword on their side behind their belt. And only the king, when he makes an exit, has a sword with him, which is held by a sash over his shoulder. The hilt and scabbard of the royal sword are made of gold.

Castane (kastane) - this is the very Sinhalese sword, or rather, a half-saber. It is really short - 50-70 cm. The blade is slightly curved and sharpened on one side, like a regular saber. Moreover, usually castane blades are European, Dutch-made. Closer to the hilt, the blade may have a brass or gold notch in the form geometric shapes most often triangles. The hilt is made of dark horn or wood, which can be overlaid with chased sheets of silver or gold if these are sabers of aristocrats. The head of the hilt is always designed in the form of a dragon's head (or a dragon-like monster). The eyes of this dragon can be made of brass (on horn handles) or precious stones, most often rubies (on gold and silver handles). The guard is complex in shape and is made of iron inlaid with brass or plated with precious metals. One of the iron "whiskers", longer, covers the fingers and ends with a small dragon head, the other two, also with dragon heads, are short, bend towards the blade and, apparently, perform a decorative function. Quite powerful langets, which go on the blade between the short mustaches of the guard, additionally strengthen the blade in the handle. The origin of this handle shape is not entirely clear. But, most likely, according to Western experts on weapons, it is associated with the shape of the hilts of Portuguese swords of the 15th century or Arab sabers of the nimcha type. Both versions are credible. It was the Portuguese who were the first Europeans to land in Sri Lanka, and from about the tenth century the Sinhalese had trade relations with the Arabs. The appearance of dragon-like heads as an element of decor undoubtedly occurred under Hindu influence. Moreover, the "dragons" on the castan are very similar to the South Indian mythical monsters, images of which can be found on weapons and bas-reliefs of temples. The teak wood scabbard on outstanding specimens, as well as the hilt, are covered with chased plates of silver and gold. Probably, on simpler castanes, the sheaths were without metal covers. This can also explain the fact that almost no scabbards for them have been preserved.

Completing short review bladed weapons Indo-Iranian region, I would like to return to the title of the series of articles read by the reader - "Bringing Death". Once upon a time, all these blades were indeed forged in order to shed the blood of the enemies of their owners. Today, they are amazing witnesses of the past, peacefully kept in museums and private collections, continuing after centuries not only to delight the eye with the elegance of their lines and finishes, but also helping us to better understand the history of the East.