At present, the MTS company, in addition to mobile communication and Internet services, offers its customers a television service. By installing a satellite dish, you can watch broadcasts from all over the world. You can use the device not only in the city, but also in the country or in country house anywhere in the country, since it is difficult to find a place on the map that is not within the company's coverage area. Installation and adjustment of the MTS satellite dish can be done both independently and with the assistance of specialists. This procedure does not cause any particular difficulties.

Key benefits of the device

The MTS satellite antenna allows the user to receive the following benefits:

  • Thanks to modern technologies and the use of the latest materials, the satellite television signal received by the antenna remains stable, regardless of where the receiver is located: in the city or outside of it;
  • Installation and adjustment of the MTS satellite dish can be done independently, since it does not require any special knowledge and skills;
  • A large package of channels available. The user can choose from sports, scientific, children's channels, as well as channels for business and entertainment;
  • Together with the antenna, a compact set-top box and a 3G-modem with a wide range of functions are supplied that allow you to watch satellite TV in HD format and change its angle for better reception quality;
  • The device parameters can be controlled without any additional devices. A built-in WiFi hotspot is enough;
  • The ability to use the Smart TV function (if the TV has such a function), which is achieved due to the high bandwidth mobile Internet channel (as a result, the data transfer rate can reach 1 GB per second);
  • The ability to record an interesting program if there is no way to watch it live.

To take advantage of the listed advantages of MTS TV, you should purchase and correctly configure a satellite dish from MTS.

Composition of the MTS TV set

The list of devices that allow you to take full advantage of the benefits of mobile satellite TV include:

  • A receiver, which is, in fact, a 3G modem. It must provide a stable connection to the Internet, as well as be able to receive and process HD format signals. Instead of a modem, you can use a set-top box of a certain modification or the TV itself, if it is equipped with appropriate devices;
  • "Dish", which receives a signal from the satellite;
  • Converter. Its task is to process the signal and transmit it to the TV. If it does not work correctly, the image will be unstable or of poor quality;
  • Fixtures for fixing a satellite dish. In addition to reliability, they must be able to change its angle in order to ensure stable reception of various channels;
  • Cable connecting antenna and TV.

Note! It is recommended to purchase the entire set in the assembly from official sellers. Since the device is technically complex, it is covered by a warranty, and if you buy it cheaper hand-held or on the market, you may encounter problems during operation. In addition, purchasing the entire kit from an official seller guarantees its assembly (coincidence of all elements) and significantly saves installation time.

Preparatory stage

Before setting up satellite TV, a number of actions should be taken:

  • Determine the location of the satellite. For this it is recommended to use special program"SatFinder", which can be downloaded from the website of the service center or specialized store;
  • Choose a place where the antenna will be installed. The ideal location is the roof, as it can rotate around its axis and change the angle to ensure stable signal reception. In addition, the higher the device is located, the fewer various obstacles that interfere with its path, which also improves the signal quality;
  • Collect all devices in unified system... After the antenna is assembled, you can start installing and configuring it yourself.

Before installing the device on the roof or other chosen place, you should prepare all the fasteners (they are supplied in the kit) and the necessary hardware (screws, dowels, nails, etc.), and also check the plug connectors for connecting the system elements to each other ...

Antenna mounting

The quality of the signal will depend on how correctly the "dish" is installed, so this issue should be given maximum attention so as not to redo the work in the future.

The installation sequence is as follows:

  1. Determine the place where the "plate" will be mounted. If the device is mounted on a wall, it should be possible to direct the antenna mirror to the south. When installing on a roof, it is recommended that you ensure that there are no taller buildings or structures in the line of sight that could interfere with the signal;
  2. Assembling the device in accordance with the requirements of the instructions. All elements must be securely connected to each other;
  3. Installation of the bracket for attaching the "plate". This will require a drill and reliable dowel nails. Using a drill, it is necessary to drill holes in the surface where the device will be mounted, and then fix the bracket on it with the help of dowel-nails;
  4. Securing the satellite dish on the bracket. It is not worth completely fixing it, since when setting up the installed antenna, you will need to turn it to improve the signal quality;
  5. Assemble the converter and point its head at the satellite. The final step is to connect the cable of the outdoor unit of the device to the set-top box.

After that, you can proceed to tuning the antenna. To do this, you need to check all cable connections and turn on the set-top box to the network.

System Setup

It is quite possible to set up MTS television yourself. This stage should be started only after the installation of the dish itself has been completed and its direction in the direction of the satellite has been checked. Before you start setting up television equipment, you should connect the set-top box to the TV using a special cable and a separate plug. If there is a cam-module included in the kit, it should be installed directly into the TV.

If all the steps for installing the device were performed correctly, the equipment will be configured automatically. The user only needs to do the following:

  • install a sim card into the set-top box's slot;
  • start the process of analyzing a 3G signal, wait for the completion of this process;
  • authorize the equipment, while viewing the channels must be allowed within 5 days (before the end of this period, all the required documents must be provided to the operator);
  • create a user profile, set age restrictions, if necessary;
  • tune the channels, after completing the search procedure, a list of them should appear on the screen.

Important! To figure out how to install the MTS satellite dish yourself and how to set up stable signal reception, it is recommended to use the instructions. If you have any questions, you should contact a specialist who can always suggest ways to improve the signal quality and answer other questions. Authorization is done in two ways: via SMS or a call to the operator.

So, self-installation and setting up MTS TV is quite possible. You can find out how to install the device from the manufacturer's instructions or by watching various videos on the Internet. They clearly demonstrate the process of assembling device elements, the order of their connection to each other and connection to the system. One of the most difficult procedures is the installation of the satellite mirror itself. To ensure a stable signal, it must be rotated frequently. This requires an assistant who will change the position of the "plate" while the user evaluates the image quality on the TV screen. In case of any difficulties, you should immediately contact the service center. This will avoid serious equipment damage and situations in which the warranty will be invalidated.

Video

In order to independently, without any practical knowledge, assemble and install a set of satellite television at home, you need to follow a certain step-by-step sequence of work.

Consider the main points to which you should pay Special attention when assembling the plate, wiring diagrams, and also focus on common mistakes that inexperienced installers make.

Installation materials

Let's start with necessary materials... To build you need:


Without them, in the presence of several heads, you will get such a tree.







It will be required if you want to simultaneously connect several TVs from one dish.

Converters

To begin with, it is worth considering the converters themselves in more detail.

They differ in polarization. There are models:

  • linearly polarized (vertical and horizontal)
  • circularly polarized

With circular, they are used to receive Tricolor TV and NTV + channels from the satellite at 36 degrees. To receive MTS and Telekart, you will need linear polarization of the Ku band.

You can distinguish them by marking. On the left in the figure, circular, on the right - linear.

They may also have different amount outputs:





The converter itself consists of three main elements:

  • irradiator
  • waveguide
  • the electronic unit

A dielectric plate can be seen under the cover of the feed. Its presence indicates that it is a circular polarization converter.

That is, it can be used to receive the Tricolor and NTV Plus channels. To turn such a converter into a linear one, to search for other satellites, it is enough to pull out and remove the plate.

By the way, the loss or deterioration of the signal can sometimes be associated with damage to this plate. Due to temperature changes outside, it gradually collapses and crumbles.

Special converters for multiswitches have 4 outputs.

However, they are all not the same. One is vertically polarized, the other is horizontally polarized. Plus two sub-ranges - upper and lower. This is important when connecting cables through a multiswitch.

Multiswitch connection diagrams

The multiswitch itself must be selected depending on the number of cables and TVs in your home. The wiring diagrams for the most popular satellites are as follows:





If you also have a regular TV antenna, then the multiswitch must have TerrTV input.

Connection diagram via a multiswitch ABS-2A satellite for receiving a package of channels from MTS:

Keep in mind that when using the multiswitch, Diseq = Diseqc is no longer needed.

Assembly satellite dish

From the assembly tool, a pair of open-end wrenches for 10 and 13 are usually enough, plus a Phillips screwdriver. For wall mounting, you need a hammer drill and anchor bolts.

When you have decided on a complete set, first of all you need to correctly assemble the plate itself. There are several nuances here.

So, for example, when assembling the traverse, note that the transverse bar, which is attached to the plate mirror itself, must be superimposed on top of it.

If you screw it on the other side, but physically it is possible, then:

  • first, you will have poor hole alignment
  • secondly, the opposite end of the traverse, where the heads cling, will go out of focus

As a result, it will initially be difficult to catch at least some signal. In addition, the mount that goes to the bracket, when adjusting the satellites above the horizon (relative to your geographic residence), should cling to the adjustable part down.

And for satellites below the horizon - on the contrary, with the adjustable part up.

Since in this case, you will no longer need to raise, but lower the mirror.

How to build a multifeed

Building a multifeed also comes with some peculiarities. In the collapsible set, there are initially two different "ears". One is more, the other is less.

The little one is put on a tube assembled with plastic.

The large one is attached to the central traverse. In this case, both ears can be positioned relative to each other in two different ways.

On the same level or in different planes. Most installers locate exactly in one plane.

However, if you do the opposite, it will make it easier to perform the very initial setup of the satellite dish and save time when looking for additional side satellites.

The assembled heads will be on different levels, one above, the other below.

Actually, like the satellites themselves fly along the horizon.

But this is of course true if your converters will catch three different satellites. When two heads catch one satellite, for example Eutelsat 36E, but with different software packages, then place them in the same plane.

But mount the third head as described above. The spread between the converters also depends on the diameter of the mirror. The smaller its size, the closer the heads will be located relative to each other.

After the bar is screwed on, try at least by eye to set the head so that the central axis of the plastic (where the two halves of the casting converge), and this very attachment to the traverse, are at an angle of 90 degrees. Further, everything will be regulated in relation to this initial position.

The order in which the multifeeds are rotated also matters. The first and closest to the plate should be the multifeed, the satellite position of which is closer to your place of residence.

For example, if you live above 40 degrees, then first on your plate should be Eutelsat 36.0E, then Hotbird 13E, and the last Astra 5.0E. The same is true by analogy with other satellites.

After fixing the cymbal on the wall or roof, lay coaxial cables from this place to the tuner or switch.

You sign each end from which head it comes from.

If you have a disec, there will be one output cable.

F connector connection

To connect coaxial cables, you need to strip them and put them on F-connectors. This can be done in two ways.

Method 1 - cut only the outer sheath of the cable with a knife at a distance of 20-25mm. The screen cannot be damaged.

Bend all the wires gently onto the shell.

Now you need to remove the insulation from central vein... It should protrude from the screen by a maximum of 2mm.

Then screw on the F connector.

You shorten the excess supply of the central core, leaving no more than 5 mm from the plane of the connector.

The 2nd way is simpler. Take the clerical knife again. Step back about 1cm from the edge of the cable and cut off all the insulation. Including outer and inner, up to the central vein.

Then, stepping back 3mm, cut off only the outer sheath.

Make sure that no lint or wire is trapped between the braid and the center conductor.

You do not need to remove the insulation anymore and do not need to bend anything. Just insert and screw on the f connector from above.

Next, do the cabling throughout the apartment in all rooms where you have TVs. You also sign all of them.

At the same time, it is much safer to run the cable directly into the device, rather than connect it through a satellite TV outlet. This can be associated with both a loss of quality and a loss of signal altogether.

The wiring diagram when using a multiswitch may look like this:

Diseqc connection

If there is only a dysik, the connection and configuration of satellites is carried out in the following sequence.

Remember that any self-respecting store of satellite equipment and similar systems always sells tuners already pre-installed on certain channels and satellites. Otherwise, competitors will simply survive from the market.

At the same time, when buying, be sure to ask the seller to write you the Diseqc switch ports, since they were exposed to them during the settings. It is on these ports that you will have to make all the cable connections.

During installation, you first connect the cables to the heads, and then wind them onto the dyseik. Just the same on it, it is advisable to connect everything initially with the “factory” tuner settings.

If you have any satellite in the receiver set to the first port, accordingly, it should not go to port number 1. If it is on the second, then the switch uses port # 2, and so on.

All input ports are always signed. The center single jack is the output to the tuner itself.

Search for satellite and channels

Setting up and searching for a satellite can be performed without fancy devices using the receiver itself.

True, you will have to drag the tuner itself + some small TV to the roof.

Unless, of course, you will install a motorcycle suspension.

Another such setting is done together. One person on the roof moves a plate, another on cell phone monitors the signal of the house on the TV.

If you are not satisfied with either one or the second option, you can buy a cheap portable device for tuning and analyzing a satellite signal from the Chinese - or here.

Then the setup will not be difficult at all. By the way, it will be useful in the future, if after strong wind your signal will deteriorate or you will want to add a satellite over time, or maybe even change heads. Set up satellites with MTS and Tricolor, instead of Amos, Astra, etc.

Start the adjustment from the center head. Initially, expose the plate with a slight rise to the horizon. In order to orient yourself in the direction, look at the nearest neighbors.

Nowadays, you will clearly not be a pioneer, and finding a pair of three tuned cymbals will not be difficult. Sometimes there are so many of them that they interfere with each other.

V last resort you can use programs on smartphones - Satellite Director or SatFinder.

Install the program, launch it and start turning the smartphone in different directions in search of the desired satellite. The coordinates of most of them are already crammed into the program and you do not need to look for anything.

The icon marked with a circle or a cross will show the correct direction for the satellite dish. Check it out.

Turn on the tuner, select the satellite from the central converter and look for at least some signal from this head. The search is performed by raising, lowering and turning the antenna itself.

The signal quality is indicated as a percentage scale and is located at the bottom of the screen. You need to achieve the highest possible value.

To do this, very, very slowly, begin to turn the plate in different directions. At the same time, the mirror itself cannot be closed.

If there is no signal, or it is of very poor quality, the cymbal lowers a little. Further, the process of turning on the sides is repeated. As soon as the signal is caught in height good quality, the plate is pre-fixed vertically.

After that, again you can twist it to the right and left to find the highest possible quality. There will never be 100%, just look for the highest possible number - 68-75%, etc.

Having found best position, finally clamp the swivel mechanism to the right and left. Just do not tighten one bolt at once to the end, otherwise the plate will be taken to the side by a couple of degrees. Tighten the nuts evenly, like on a car wheel or on an engine head.

When the corners are all set, it is necessary to adjust the entire structure in height again. Having loosened the fasteners, you begin to raise or lower it vertically, all the while controlling the signal.

Remember that the maximum is always sought by going down.

What is it for and what does it give? During long-term operation under the weight of snow, wind, rain, the saucer will still go down a little, worsening the signal.

You also need to put it on a stretch. This will preserve the signal quality for a long time.

Keep in mind that the plate should initially be mounted on a wall or roof at exactly the same level.

If this is not the case, then having found the maximum of the signal along the horizontal, you will start looking for the max along the vertical. And in the process, the horizontal position will go away. You will have to adjust the horizontal-vertical several times.

Then proceed to the next stage of the setup - scrolling around its axis of the central converter clockwise or counterclockwise. Here you can also achieve an improvement in the signal by a few percent.

This will set up the cymbal itself and the center head. Let's move on to setting up side converters from other satellites.

Switch the tuner to the next satellite and call up its information line. The converter of this satellite, also thanks to the multifeed, can be rotated up and down, zoom in or out from the dish.

As with the middle head, first look for the maximum on the vertical, and then move the side converter closer or away to the central one. At the end of the settings, rotate it around the axis.

When tuning satellites from side converters, pay special attention to where you are standing in relation to the dish. On the side heads, the signal from the satellite enters the center of the mirror and is reflected, as in a billiard, to the converter.

So, in order not to block this signal with your body, you should be located on the closest side of the adjustable head, and not on the opposite.


After searching and tuning the satellite from all three converters, the process can be considered complete. Hide and seal the dysik from rain and precipitation, and also secure the satellite cables with cable ties so that they do not dangle in the wind.

Installation and connection errors

1 Incorrect assembly of the crosshead

At the very initial stage, do not make the mistake of attaching the traverse to accommodate the converters. It should be installed under the bracket, not on top of it.

Otherwise, there will be big problems with finding a signal even on the central head. The wrong focus will be to blame.

2 Using loop-through sockets

Pass-through sockets are the first enemy of satellite television. From such devices, there may not be a signal at all.

Therefore, only terminal can be used. They are often paired with television.

3 Splitters

They can only be used for analog television. Satellite TV should not have any splitters. The fact is that the transmission of channels usually occurs at two polarizations.

And the splitter is not able to simultaneously pass them through itself. As a result, some of the channels on some TV will simply be absent.

4 Large number of connections

Any connection is a loss of signal quality, including at seemingly convenient sockets.

Take special care that there are no connections in places of high humidity - attics. In bad weather, the signal will disappear altogether because of this.

5 Cheap cable

Do not buy a Chinese cable of dubious production. Almost half of the signal level that reaches from the cymbal to the receiver can depend on the quality of the cable.

6 Incorrect Diseqc insulation

Never wrap a dysec in plastic bag... Even if this will save you from direct raindrops, condensation will still form inside over time.

And it is he who will cause the switch to fail, which necessarily requires ventilation and communication with air. The easiest and cheapest option is an empty plastic bottle, which also doesn't help much.

Therefore, it is best to place a waterproof box next to the plate and install the switch in it.

7 Insulating F-connectors

Also, do not tape the F connectors. Such insulation does not help much against rust, and only worsens the situation, since sooner or later moisture will still penetrate under the electrical tape.

And instead of gradually evaporating or rolling off the connector surface, it lingers on it and accelerates the corrosion process several times. Also remember to put the insulating cap on the free Diseqc port.

I want to watch TV with pleasure. This requires not only a good program or film, but also great quality Images. Cable television is far from operating everywhere, so today there is an alternative that provides the opportunity to view many broadcast channels even in the most remote corners of the country. Thus, you can watch satellite TV and enjoy beautiful picture... Due to the variety of suppliers, it is possible to choose a suitable operator. How to set up satellite TV from MTS independently will be discussed in this article.

To install and configure satellite television in the MTS system, you yourself need attention and certain knowledge, otherwise the equipment can be damaged. First, you need to check the connectivity, that is, determine whether your region is within the coverage area, and also whether there are any obstacles to mounting the antenna, for example, a tall tree or a house. In addition, before installing and adjusting the antenna, you need to make sure that you have purchased a kit with all the necessary elements.

So, setting up MTS satellite TV includes the following steps:

  1. Choose a place for mounting a satellite dish, where it will have a direct line of sight to the satellite.
  2. Assemble the antenna according to the instructions that came with it.
  3. Install the equipment mounting bracket as firmly and securely as possible in the desired location.
  4. Attach the plate to the bracket according to three parameters: swivel, swivel and tilt.
  5. Connect the MTS set-top box and set up satellite TV using the installed mobile app online.
  6. Check the signal strength in the Antenna Settings section of the TV.

This completes the do-it-yourself MTS satellite TV setup. If you have any problems, admin will answer all questions. Read on for more detailed information connections.

Antenna installation process

The quality of the satellite signal reception depends directly on the correct tuning of the antenna from the MTS. Just buying a set of devices and materials and putting on a plate is not enough. You need to choose the right direction to the satellite, connect the receiver, and make certain settings.

First, you need to decide on a place. The satellite dish must always face south. It is good when the windows face south. The main thing is that there is no tall building or tree nearby that will block access to the satellite. Otherwise, you will need to output and install the plate on the roof of the house. Next, bolt the bracket, and the plate itself to it. In this case, it is necessary to use not all the bolts at once in order to be able to adjust the desired degree of the angle of inclination of satellite TV from the MTS. The next step is to mount the converter, which must also be turned to the desired degree.

Setting up the receiver head with your own hands is considered an important task. The equipment will not work correctly if it is even slightly away from the satellite. In this case, you can set up a satellite dish from MTS yourself in three ways. Using a smartphone will help you complete the task using installed application SatFinder, specifying the name of the satellite in which you can calculate the required tilt and turn angles. The second way is to use the MTS website in the "Satellite TV" section, then "Settings", and then "Coverage Map", "Settings Wizard". The last method will help after installing the console in the "Settings" menu. To tune the antenna from the MTS as quickly as possible, watch the video with instructions.

Necessary equipment

The set of equipment from MTS for the installation of satellite TV is as follows:

  • antenna;
  • Cam module or set-top box;
  • converter;
  • bracket;
  • 2 ° F-connectors;
  • coaxial cable;
  • a set of screwdrivers and keys.

In addition, you may need a plug, and in the case of connecting two TVs - a divider.

Setting up the receiver

In order for the setup of MTS satellite televisions to be successful, you need to set up the receiver. Connecting a TV set-top box requires an antenna cable to be connected using an HDMI cable to the TV connector. To completely complete the satellite TV setup and connect the receiver, you need to do the following:

  1. Insert the SIM card into the slot provided for this.
  2. Turn on the set-top box and wait for the end of the equipment analysis and initialization of the 3G signal.
  3. Authorize the device using the methods that appear on the TV screen, usually a call to the call center or sending an SMS, in some cases the service will be performed automatically.
  4. Create and save a user profile. At this stage, in the "Access level" section, you can adjust the age threshold and change the password.
  5. Scan available channels.

TV module

To configure the module, you need the following steps:

  1. Disconnect the TV from the mains.
  2. Connect to it antenna cable through the connector marked SATELLITE.
  3. Install the TV module into the CI port.
  4. Install the smart card into the TV module so that the chip on it looks towards the TV image on the sticker.
  5. Turn on the TV.
  6. Go to the mode of viewing satellite TV from MTS, set the necessary parameters.

Settings for satellite TV from MTS

The MTS TV set using the STB Dune HD TV 251-S2 set-top box for watching satellite TV does not need additional channel settings, everything will be done automatically. Manual settings will be needed when using the Verimatrix CAM module. In this case, the satellite must have the parameters 75.0E ABS 2 MTS TV, the polarization is applied vertical linear, the position is 75 ° E, the module type is DVB-S, DVB-S2, QPSK, 8PSK, the speed is equal to 43 or 45 Ms / sec, and FEC is 5/6, 2/3.

Manual Channel Tuning

What settings do you need to watch channels? Manual settings are only needed for the CAM module. For this, a list of the frequency range and transponders is used.

Features of connection to satellite TV MTS

The satellite, thanks to which the channels from MTS are broadcast, has a vast coverage area. This operator covers the territory of Russia by 90%. Main feature Provider is focused on the quality of the received signal and image quality, the number of channels fades into the background. For some channels, it has several versions of the standard time. For example, if you did not have time to watch a movie or program at one time, then on this channel you can see it on this channel, only in a different time zone.

Registration in the personal account of MTS satellite TV

A personal account on the MTS website allows you to receive many privileges. To register, you need to select the "My MTS" button, which is located in the upper right corner of the site, and then decide on the required section of satellite TV. To register, you will need to enter the contract number and passport data. Such actions in the future will make it possible to manage services, view payment history, make settings, view the current tariff plan and change it, pay for the service, find out the rest of the traffic, and more.

The MTS company today offers its subscribers not only mobile communication, now customers can connect to themselves and enjoy high quality broadcasts of many channels. But for high-quality viewing, you will need to set up home television, and how to do this is described in the article.

What you need to connect

Each person who decides to watch TV from MTS will need to use the following equipment to connect:

  1. TV set.
  2. A device from MTS that you can buy at your choice: an interactive set-top box with support for broadcasting in HD quality, which has a 3G modem for Internet access, a regular TV box that can broadcast HD channels or a TV module (CAM) ... The latter device allows you to use satellite TV without a set-top box. In addition, the module can reproduce broadcasts in HD quality, but such equipment will require a TV that has a DVB-S2 receiver with a CI connector.
  3. Satellite dish, which is included with the purchase of the equipment.
  4. The converter is also included in the standard equipment list.

In addition to the devices described, the following components will be additionally needed:

  1. Antenna cable and fasteners. Such components will already be supplied in a complete set from MTS.
  2. Remote Control.
  3. HDMI to HDMI cable or Jack 3.5-3RCA cable.

When everything you need is ready, you can start connecting and configuring. This can be done with the help of a wizard from the MTS company, who will go to the site to connect. You can order the customizer service at the time of ordering. Another method is to self-configure the equipment, according to the instructions included in the kit. Below will be described a detailed method of connecting one or another equipment with your own hands.

Preparatory work

  • Check the possibility of installation. To do this, you can use a free mobile application that is available for download in the application market. It is called "SatFinder", after installation with it you can see the location of the satellite in relation to the house where the TV will be used. The program allows you to find out the exact direction, as well as indicate how to correctly install the antenna.
  • After checking the installation feasibility, you will need to familiarize yourself with the physical installation of the antenna, as well as identify possible interference and obstacles to the signal. If on the signal path there are tall trees, at home, etc., then it makes sense to put it on the roof, only then it can be twisted in different directions to improve the signal.
  • Further, the equipment itself is selected for the TV used, in other words, it is a set-top box or a module.

Additionally, before installation, you will need to check the presence of all the necessary components:

  1. Prefix or module.
  2. Smart card or sim card.
  3. Antenna.
  4. Antenna mounts (must be supplied).
  5. Converter.
  6. Coaxial cable.
  7. Connectors.
  8. Installation tool.
  9. Plug for connecting the cable to the TV.
  10. If 2 TVs are connected at the same time, then a divider that works in the range from 950 to 2150 MHz.

To make installation and setup faster, and much more convenient to work, it is recommended to immediately buy the full set, which is offered by the MTS operator. It will contain everything you need for installation.

Antenna installation and tuning

First you need to assemble and install the antenna. The assembly procedure is described in detail in the instructions; it is quite simple to work on it. It is necessary to tighten all the nuts, but so as not to damage anything, but there is no need to touch the nuts and fasteners for the wall bracket and adjusting the antenna angles. The mount, which is made of a couple of parts, must be assembled separately and not screwed onto the antenna. The converter is immediately installed on the antenna, but the cable is turned on later.

Next, using the application described earlier, you need to install and fix the antenna on the wall. Installation is carried out on a flat surface, the bracket itself is attached to it, and the attachment points are outlined with a marker. Further, the marked area is drilled and, using the dowels, installation is carried out. Then, you need to put the antenna on firmly installed brackets and tighten the nuts on the fasteners, after which the angle of the mirror is set vertically as much as possible.

When the base is installed, the cable is connected to the converter and the antenna can be tuned. To do this, you need to rotate it, tilt and unfold the converter. The procedure will be as follows:

  1. On the mobile phone the SatFinder application starts.
  2. The satellite ABS 2 - 75 E is selected.
  3. The application will start showing the direction of the selected satellite, and the camera will need to show the position and the required angles of turns and tilts.

After setting the antenna, you need to check the signal. The cable must be connected to the set-top box and go to the settings with the remote control. Go to the section with antenna settings, where the signal level will be shown. With a weak signal, you need to twist the antenna in different directions to achieve high-quality communication. As a rule, the connection quality with the application will be high and no additional settings are required. When the signal is at the desired level, the antenna is fixed, and all the nuts are tightened.

Setting up MTS equipment

To set up the equipment, you will need to turn on the set-top box, having previously connected the cable. When using the module, you need to insert it into the TV, into the connector intended for it. Then the card is inserted.

Setting up an interactive set-top box will be as follows:

  1. Initially, a SIM card is inserted.
  2. Next, the set-top box starts up and you need to wait for initialization.
  3. After that, you should go through authorization using the methods that will be offered.
  4. After authorization, you need to create and save your profile, and in the tab with the access level, if necessary, put a password or age restrictions.
  5. Then there will be a channel scan procedure and a menu with the found list will open.

This completes the setup procedure. Setting up a conventional TV box with HD broadcast will look like this:

  • In a disconnected set-top box, you need to insert SIM cards and then turn on the set-top box to the network.
  • A green lamp should light up on the front side, if it is not there, then you need to press the red button on the remote control.
  • Next, the TV turns on and it should be switched to AV or HDMI mode.
  • The initial installation menu will open, where the language, picture size and other settings are set.
  • To search for channels, select on the remote control, press the search key and then click on "OK".
  • When the search is finished, the TV will show any channel found and the search menu will close.
  • You also need to make sure that the device is authorized, if this is not the case, then it is better to do the authorization yourself by clicking on the link https://lk.ug.mts.ru/#/satellite.
  1. Unplug the TV and plug in the antenna cable using the SATELLITE connector.
  2. Further, the module is installed into the port on the TV, a smart card is inserted into it, and only then the TV is turned on in the network.
  3. The screen should say that the module has been found. To watch broadcasts, you need to select the reception of a satellite DVB-S2 signal, and then make the setting, you can see it in the instructions for the TV and, if necessary, register them manually.
  4. To watch TV from MTS, you need to set the reception on TV DVB-C signal and write the following parameters: in the column with the search type, network or fast is indicated, for the signal frequency you need to select 298000KHz, in the line with modulation - QAM64, and the symbol rate will be 6875Kps.

After that, the broadcast should begin. If setting up any type of equipment did not give results, then it is recommended to call the support service on free phones 88002500890 from a landline or mobile number or 0877 if the call is made only from a mobile phone.

Installation and configuration of satellite TV MTS.

Questions about this article?

On this page you will find the following information:

What you need to know before getting equipment How to install and configure an antenna without using expensive equipment How to authorize equipment How to set up an interactive MTS set-top box How to set up an MTS HD set-top box (for linear TV) How to set up a cam-module for MTS satellite TV More informative video instructions.

In other words, here you can get all the information on how to install and configure MTS satellite TV without the help of others, including also installing an antenna with your own hands.

Before purchasing and installing an MTS satellite dish.

Check out the techno installability.

Your region should go into the satellite coverage area. The map is color coded - if the area is red, a larger antenna is likely to be useful.

If you live outside the Russian Federation, the signal quality is not guaranteed. If your region is within the satellite coverage area, then before deciding on the installation of satellite television, we recommend using the "SatFinder" application (available in the AppStore or Play Market). It will show the location of the satellite relative to your home and help you find a clear direction in which the antenna should "look" (for more details, see this article). Then check if there is a possibility of installing the antenna on this side and if there are any obstacles nearby (adjoining tallest house, trees, etc.). From time to time, it makes sense to reinforce the antenna not on the wall, but on the roof of the building, where it can be turned in any direction. The signal from the satellite must always be in direct line of sight from the antenna, otherwise there will be obstacles to the signal quality.

Pick up equipment for your TV set.

In total, MTS offers three equipment options:

Interactive set-top box (for watching interactive TV with an extended set of options). Interactive TV needs a 3G MTS signal to be fully functional.

CAM module: suitable for TVs with an integrated DVB-S tuner. Be sure to make sure that your TV set is equipped with it before receiving the cam-module. It often happens that even new TVs do not have this tuner built-in.

Linear HD-set-top box: universal equipment for MTS linear satellite TV, supported by most TVs.

Before setting up MTS satellite TV, check if you have all the necessary equipment:

Set-top box or cam-module with smart or SIM-card Antenna Bracket for antenna (complete with antenna or separately) Converter Coaxial cable two ° F-connectors A set of keys and screwdrivers.

Additionally, you may find it useful:

Plug for connecting a cable to a TV set Divider operating in the spectrum from nine hundred and 50 to two thousand 100 50 MHz (as needed, connect 2 TVs)

Installation and configuration of the MTS satellite dish.

Observe safety regulations when working at heights and working with power tools!

Assembling the antenna.

The annotation describes the entire antenna assembly diagram, it is quite ordinary. Tighten the nuts gently without damaging the body and bracket fasteners. The cymbal angle option does not need to be tightened to the wall bracket and nuts. Assemble the 2-piece bracket separately and do not attach to the antenna itself. The converter can be connected to a plate on this moment(or do this when you install the antenna), and the cable will need to be connected later. Fastening the antenna to the wall.

Before purchasing the equipment, we recommended choosing a suitable location for installing the antenna using a special application. Choose a very flat surface at this location for attaching the bracket. Attach the bracket, trace around the mounting holes with a pencil or a marker, and after drilling them, attach the bracket using dowels. Tighten the screws so that the bracket is very firmly attached to the wall (apply force to it to check the firmness of the fastening). Then "put" the antenna on the bracket, tighten the nuts on the mount and adjust the angle of the mirror very vertically.

If you have not done this earlier, then install the converter in the holder, pointing it with its head towards the cymbal.

Strip the cable and install the F-connectors on it (detailed annotation - here). Connect the cable to the converter. Setting up an antenna for satellite TV MTS.

Video about setting up an antenna for MTS satellite TV.

If you want to connect multiple TVs to one antenna, use the tips in this article.

Setting up MTS TV equipment.

To connect the set-top box, screw the antenna cable to it, and use the HDMI cable to connect the set-top box to the TV set. To connect the cam-module, completely plug it (without an access card) into a special connector on the TV set. Make sure the module is fully seated in the slot. Then insert the access card into the CAM-module with the logo from the TV set. The side of the card with the chip must face the CAM module.

Setting up an interactive set-top box for satellite TV MTS.

Before turning on the set-top box, insert the SIM-card into the special slot. When the unauthorized equipment is turned on for the first time, the 3G signal is analyzed and initialized. You need to wait for the end of this process. Next, you need to go through the activation (authorization) function of the set-top box - available methods will be offered for you. With any authorization method, the service will be available in demo mode for 5 days until the operator receives the originals of your signed documents. The next step is to make and save the user profile. In the section "Access level" you can set the age threshold and set / change the password for access (by default the password is 0000). Next, start scanning available channels(press the appropriate button). After scanning the frequency spectrum, a window with a list of the found channels will appear.

After that, the setup of the interactive set-top box can be considered complete.

Configuring HD-set-top boxes DCD four thousand four hundred and four for satellite TV MTS.

With the TV receiver disconnected from the power supply, carefully insert the smart card into the dedicated slot. Connect the TV receiver to a 220V power supply. On the front panel of the DSD4404 TV receiver, a green indicator will light up, otherwise turn on the set-top box by pressing the reddish button on the remote control. Turn on the TV Set the TV to AV or HDMI signal reception mode. When you turn on the TV for the first time, the “Initial installation” menu will appear on the TV display, in which you can set the menu language, image size, as well as set the satellite, transponder and LNB options. To start searching for channels, press the navigation buttons ▲ ▼ on the remote control, select "Search" and press OK. After the end of the search for channels, the TV receiver will exit the menu and start broadcasting the first found channel. To interrupt the channel search, press the "Exit" button on the remote remote control... Make sure that your equipment is authorized, or activate it without the help of others through the form at the link https://lk.ug.sputnikmts.ru/#/satellite, otherwise the service will end in 5 days.

Setting up a cam-module for MTS linear satellite TV.

Disconnect the TV set from the mains. Connect the antenna cable to the TV set through the connector marked SATELLITE. Carefully insert the TV module into the CI port of the TV set. Pay attention to the CI port connectors and the TV module connectors - they must match. CI port placement - depends on the TV manufacturer. Install the smart card into the TV module so that the side of the smart card with the chip is oriented towards the sticker with the TV image. Turn on the TV set to the network, after which information on the presence of the CAM module will appear on the TV display. To start watching MTS Satellite TV, put your TV set into the satellite DVB-S2 signal reception mode and configure it as described below.

characteristics (choose a suitable satellite or add a new one with these options):

- Modulation - DVB-S2, 8PSK.

- The frequency of the reference / home transponder is 11920MHz.

- Symbol rate –45000 Msymbol / sec.

- LNB polarization - vertical.

- LNB local oscillator frequency - 10600MHz.

- LNB Power - On.

- Tone 22KHz - on.

- Search type - "Network" or "Fast"

The description of navigation through the interactive menu and the use of the above options are you.

can be found in the annotations for your TV set.

11740 MHz | SR 40 three thousand | FEC 5/6 | Vertical.

11800 MHz | SR 40 5 thousand | FEC 2/3 | Vertical.

11860 MHz | SR 40 5 thousand | FEC 2/3 | Vertical.

11920 MHz | SR 40 5 thousand | FEC 2/3 | Vertical.

11980 MHz | SR 40 5 thousand | FEC 2/3 | Vertical.

12040 MHz | SR 40 5 thousand | FEC 2/3 | Vertical.

12100 MHz | SR 40 5 thousand | FEC 2/3 | Vertical.

12160 MHz | SR 40 5 thousand | FEC 2/3 | Vertical.

Ask our specialist a question.

ANSWERS TO YOUR QUESTIONS.

Hello. I got a set of satellite TV in the salon in Kaliningrad.

I installed it without the help of others and tried it, without the help of others, to configure it, according to your advice. Signal zero. I called the tuners, but not MTS, but others.

Checked the signal with the device, do not configure.

They explained that a small plate, etc.

There are no those. ability to customize normally. I tried to hand over the set back, they said that it was refused because there is no statement about the impossibility of installation.

And if I myself would set everything up, then in general, what an act. To me for these calls, options to pay, how much this displeasure will ultimately cost. Divorce is not different. To file a tribunal, or what? And in defense of consumer rights. Made a gift for New Year spouse. I have a pension, and so everything is rapidly ending without such spending.

Hello. Our website has a satellite coverage map where Kaliningrad is marked as a weak signal area. We always advise you to study all the information before buying.

A set of equipment has now been delivered on a preparatory request. But the antenna (dish) and sensor are not from MTS but from another company - it is written by Lumax. Maybe this is the case, or the whole set must be from MTS.

Yes, this can be, these are new sets, for some reason MTS decided not to paint on their plates.

Good day. In the insert to the TV module, the frequency is indicated as 11913, the speed is 45, the frequency of the local oscillator is 10600 - other characteristics are written here. What should I enter?

Good day. The annotation contains outdated information, in the fall MTS transferred broadcasting to a new satellite and the characteristics changed. Here are the correct ones:

Signal frequency - eleven thousand nine hundred and 20 MHz; Modulation - 8PSK; Symbol rate - 40 5 thousand Msymbol / sec; Polarization - Vertical (V); Search type - Network.

Good day. We got a set of satellite TV, installed everything but no signal. Prompt antenna and converter options. Nizhny Novgorod region, Lukino village, st. Cooperative house 41.

Good day. Answered for you on another page.

Good day! When connected, we encountered a discrepancy, on the TV display the inscription "overcurrent on the antenna". What does this mean and how to solve it?

Good day. This means that there is a short circuit here and there. You need to check the entire cable and its connections.

Hello. I bought for myself a set of satellite TV included, the s2-3900 receiver didn’t twist the dish, but the receiver says there is no service. Maybe a receiver with glitches. It can be changed separately so that the whole set is not disassembled and not taken to the store.

Hello. Hardly a receiver with glitches. But they will change it if it is really faulty, and earlier it will be sent for diagnostics. Therefore, yes, at first it is necessary to carry only the receiver - to the service or the mts communication salon.

Hello! purchased a mts prefix! we live in Sverdl Oblast, Reg.district, village Aramashka. we cannot find the satellite. indicates only the Kuban satellite why?

Hello. Perhaps the direction to the satellite, the placement of the dish, was mistakenly chosen.

Tell me the direction of Irkutsk region Nizhneudinsky district, village Katarbey.

Please do this without the help of others using the tips in this article.

Hello, I bought a piggy bank with a cam module 31st. I'm trying to set everything up. The TV set is also new, the menu is new. Faced with a signal problem, and the fact that I can not understand what Options to write for the transponder. On the phone, I was told the frequency 11913, the video is different, but at the end there is a whole list, I would not want to sort them out, because I also have to turn the antenna.

Hello. The frequency of the reference / home transponder is eleven thousand nine hundred and 20 MHz.

Good day. I bought a set with a TV module. Need to activate first and configure later?

Good day. No, set up first and activate later.

Krasnoyarsk region. The village of Emelyanovo. Please tell me the characteristics of the tilt of the antenna and the converter.

Please condition the referral without the help of others using the advice in this article.

I bought a set yesterday (plate and receiver, in the mts store). I caught the signal (100% / 65%), set up the channels, but they are not shown (the smart card is not registered). When you send an SMS with a card number and a chip number, “a contract with such a card has already been concluded”. What to do? You can't get through to those support, you hang on the phone for an hour.

This issue must be resolved only through technical support or the MTS communication salon. If you write here all the data (full name, contract number, set-top box number, smart card number) - we can find out ourselves, but after January 1 (the 31st website administrator is not working).

Hello, how to find out your own Login and Personal account?

Hello. The answer to your question can be found at this link.

how to drop options from the MTS satellite television control panel.

There is no such function, you can only set up pairing with another TV.

Hello, please tell me Kana HOUSE OF KINO is included in the basic set?

Hello, no, it doesn’t come in.

Hello, I bought equipment with a Cam-module, but it turned out that I did not have a satellite tuner on my TV set, I can configure the module myself through an ordinary satellite tuner that is not integrated into the TV set and what frequencies to hammer.

Hello, yes, if you have a DVB-S2 satellite receiver with a slot for a cam module, then you can. By frequencies - see the annotation on this page about the cam-module.

write the number of those support.

Vladimirskaya oblast, Sudogodskiy district, Konyaevo village, tell me the direction, as it is always different from the mobile application.

Azimuth (Value for postponing the direction of the protractor on the map) 140.35 °

Magnetic bearing (Value for deferring compass heading) 129.43 °

Tilt angle (How much to tilt the mirror of the antenna of relativity of the earth's surface): -5.68 °

Elevation angle: 19.32 °

Converter rotation (look at the converter from the side of the dish and turn counterclockwise) -20.96 °

How to sort channels.

What equipment do you have (set-top box model, module)?

Hello, I bought a ci module for tv, can I set it up without a plate and without any prefixes. I bought it in the MTS salon and they told me that the basic package was connected.

Hello. The satellite cam module will not work without an antenna. But the antenna does not have to be MTS - it may not matter what other satellite dish.

And for someone, in general, this plate indicates. hike this is such a strive ... acquired and no one can catch the signal ... now it's not mind-boggling why such a discount ... .people don't get fooled ... .this is a walking scam ... .it's better to take more expensive but better ... .ntv or tricolor ... .and not any troubles.

Those who were able to catch the signal simply do not write here: why write when everything works fine? The equipment is working properly, if configuration tasks appear, call the installer.

My signal strength is always 30% and I can’t catch the satellite. How many did not turn always 30.

In general, the situation is weird, because the signal strength must change when you rotate the antenna. But we cannot help you remotely - try to call MTS technical support or call a personal foreman.

What options do you need to enter the city of Kingisepp Leningrad Region.

Options must be defined not for the town, but for a specific address, otherwise they will not be accurate. Read more about this at this link.

Hello! when connected, it writes an overcurrent on the antenna. what is this?

Hello. In most cases, this means that a short circuit has come out. Visually inspect all cable and connections. It can also happen due to incorrect installation of the F-connectors.

Good evening !! So my problem was resolved, as I previously wrote from TV LG49UH619V The motherboard block came from the city of Ruza, Moscow region .. installed the unit and just went into the satellite options, the signal went 100 percent and the quality was 100 percent. It turns out that the problem was in a brand new warranty tv I accept Supral 0.9 and Inverto Black Ultra converter on the Plate. The signal is not lost even in heavy snow.

Hello! We are very glad 🙂 Thank you for unsubscribing!

What options do you need to drive in Ryazan region the village of Sergeevka, 454. Who is already Tiri for a day I am struggling to install the antenna indicates a zero signal. Will be kind enough to help with the options.

We did not find the house you indicated on the map. Try to find direction without the help of others using the methods described in this article. But the discrepancy may be not only in the incorrect determination of the direction to the satellite (we assume that in three days you have already tried to turn it in all directions, and some of them would have already turned out to be correct). When you find the correct direction vector of the antenna, look if there are any obstacles in the direction of the satellite, if you are using a suitable converter, if the cable is in order.

Have a good time of day, I bought a set of mts with paid viewing for one month in their salon, filled out the contract. After installation, I did not call the mts. When connected, the TV set displays "no service". Could this mean a lack of activation or something else?

Have a nice day. This discrepancy is connected not with the lack of activation, but with the fact that the satellite signal is not received by the receiver. In other words, either the antenna is oriented incorrectly, or there are obstacles in the signal path from the satellite to the antenna, or something with a converter or cable.

There is a satellite dish that previously worked on Yamal 202, will it work with the MTS TV set-top box, respectively, when tuned to the MTS satellite?

The antenna will work. But maybe it will be necessary to change the converter - look at what spectrum you received the signal from the Yamal satellite two hundred and two and, if necessary, change the converter to a linear Ku-band. And of course, you will need to redirect the antenna to another satellite.

Ya zhevu v Tadzhikistan u menya shas ne rabotaet Abs 70 5 / ranshe rabotal s modul mts.

Hey! The satellite coverage area has changed, and at the moment in Tajikistan, indeed, there may be no signal.

Good day!! Now MTS was connected, the master activated everything via the phone, the operator said that it was necessary to conclude a contract. how and where to conclude it.

Good day! If you took the equipment from a dealer or in a communication salon - you should have concluded a contract with you, contact the place of purchase. If you received the equipment in a retail network (Eldorado, DNS, etc.) or in an online store, the contract is not concluded in this case.

This TV set does not support satellite cam module.

Will the set of equipment work with the cam-module if there is no threaded connector for the antenna cable?

The lack of such a connector on the TV is an indirect sign of the lack of a built-in tuner. And without the tuner built into the TV set, the cam-module will not work. If you tell me the TV model, we can answer more precisely.

as I wrote earlier. I still can not configure the LG 49UH619V TV set with a cam module for mts. called the master through the support service. the master came by phone with an MTS specialist in setting up satellite television. and this and that, he still could not set up. Will change the motherboard in the TV set under warranty. but again to say that it is not a fact that it will demonstrate. type that can be problemma in the plate. in response, I connected the DS300A receiver to him and in a matter of seconds the receiver found two hundred and one channels .. the master was at a loss. At the same time, I think that if the dish had been incorrectly tuned, then the receiver would not have caught and demonstrated anything. if I'm wrong, correct.

You are right, if the antenna is incorrectly tuned, the receiver would not work.

I bought a set and installed it according to the characteristics as written in the annotation. But for some reason on the TV set there is no POWER AND PROPERTIES.

Antenna is misaligned.

I bought a set of MTS satellite TV on a good day, installed an antenna on the device and with the help of a program on the phone, on the receiver the scale of strength and quality does not rise. The cable is ringing out is not damaged, tell me what to do and where to go?

Good day. Try to rotate the antenna and converter while observing the scale on the receiver. If nothing changes, it is better to contact a specialist in setting up satellite TV.

In other words, in order for my satellite television to work, do I need to take the full set separately?

As we figured out, you already have an MTS set-top box connected and working. To connect a second TV set, you got a universal cam-module (which MTS will not decode channels). Right? Then, in order to watch satellite TV on a second TV set, you need to purchase an MTS cam-module, without an antenna. The 2nd TV set itself to the antenna, if we figured it out correctly, you have already connected it.

Good day! I got a universal cam module stuck a SIM card from the set-top box, but the channels do not show, they write that the signal is encoded or weak, can you help me decide?

Good day. The card will work only with the equipment (set-top box or cam-module) with which it was sold, because the MTS system stores scientific data - the module number and the card chip number. Only when they match can the key on the card decode the signal.

Nice evening, we can't set up the universal remote control. The volume and channels were switched over, and the rest does not come out in the same way.

A good evening, we will not be able to assist you remotely - this problem must be solved by being in touch with the technical support operator and following his advice.

Good day. I got a set of MTS TV and only after that I found out that the satellite is on the other side of the house in which I live. Do not install the antenna on the roof. Can a set be returned?

Good day. By law, the merchant should not revert such a product, but many do. Therefore, it is better for you to settle this issue where you received the kit.

I bought the module itself in the web store, on the Samsung TV set, insalization is going on in 5-8 seconds, it is lost on the Samsung s9 receiver, the module itself sees the version, etc. fta channels seem to be encoded, what should I do?

Gennady, please formulate the situation correctly. We have not figured out anything from your story.

Hello! How to set up a program schedule for satellite mts tv

Hello. What kind of TV equipment do you have?

Hello, we installed satellite equipment, connected it to a TV set, downloaded the mts, the signal is zero, and the inscription is no service, what does it mean.?

Hello. This means that there is no signal to the receiver.

You are not reading carefully !! The module is worth it. I write that there is no signal level and properties. Cam module, simply put-paid-gives permission to view. Even without a cam module .. the TV should show the signal levels. But they are not.

Yes, I'm sorry. If we figured it out correctly, you have a prefix, everything works fine with it, but not with the module. It means that the discrepancy is not in the antenna-converter-cable, but in the settings of the TV and cam-module. It's better for you to contact technical support, the operator will help you step by step to configure the cam-module.

Good day. When connecting an antenna satellite to the receiver, everything works and indicates. But if you switch the TV cable to TV LG49UH619V, then there is no signal at all. as expected, I enter a transponder eleven thousand nine hundred 20 speed 40 5 thousand further DVB-S2 everything is as expected and the signal and properties are zero percent. What could be the reason?? maybe the TV tuner is not good. I inspected the power to the converter everything goes, that is, the LNB is turned on. polarization is vertical. or it may be necessary to enter the characteristics of the satellite ABS2A .. with the satellite ABS2 does not want to work.

Good day! In order for satellite TV to work through the tuner integrated into the TV, it is necessary to install the MTS cam-module in it.

New channels "A2" and "TV XXI" on which transponder are broadcast?

MTS does not have these channels.

Nice evening! Please tell me where in Vladimir you can change the convector?

Hello. In Vladimir, the converter can be purchased in specialized stores, for example, here: sat33.ru.

Good evening, I understand correctly, if the equipment is installed and configured correctly, and the message “no service” is flashing on the TV display, does this mean something is wrong with the convector? I beg you to answer, I don’t sleep for the second night ...

Good evening! Andrey, your direction of thought is correct. In general, all equipment is an antenna, a converter, a cable and a receiver. The first three components are responsible for ensuring that the signal goes to the receiver. Accordingly, if it does not come to it, then there is a discrepancy either in the antenna, or in the converter, or in the cable.

Hello! Is it possible to order your antenna with all the equipment and installation at the dacha in Chekhov and how much will it cost?

Hello! This cannot be done on this website, the website is informational. You can contact an MTS communication salon or a dealer. We can give you a hint about the price if you tell us what kind of equipment you will need for a TV set (a linear or interactive set-top box, cam-module), you also need a subscription for a year or a month. The price of the option is determined by the expert on site and depends on the difficulty of installation. Usually it fluctuates in the range of 1500-3000 rubles.

We live in Buryatia. Time on MTS indicates 5 hours later than the regional one. How do I set the plate time for our region?

In general, the time on MTS satellite TV should be in the capital, it will not be possible to reconfigure it.

Can the TV set work as a set-top box, that is, support interactive functions.

The same as on the MTS console? no.

tell me and the radio channels are interactive that the usual set of radio channels is not.

MTS has no radio yet.

Hello, can I connect mts TV to a regular TV set through the tuner.

Hello. If the TV has a connector that allows you to connect a set-top box to it, then yes.

Hello, how to check the antenna signal level on the s2-3900 set-top box.?

Hello! In the "Settings" section of the menu, there are two scales at the bottom - the quality and the signal level.

Hello, please tell me, the TV has a connector for the ci cam module, but there is no LNB output, there is only an ordinary antenna input. Will satellite TV work through the module and antenna input?

Yes, it will. The main thing is to make sure that the TV set has an integrated tuner for the DVB-S2 format.

There is a set of MTS TV apart from the receiver. Can I connect a receiver from the tricolor.

This can only be if you want to watch Tricolor TV (in this case, you will also need to change the converter on the antenna). If you want to connect to an MTS provider, you need an MTS receiver or cam-module.

what to do if you do not catch the signal?

Hello! At this point, I am using tricolor TV, I want to switch to MTS, can I throw an old plate and a gun, and buy only a cam module? Will it work?

Hello! The antenna can be dropped, but redirected to another satellite; the converter will need to be changed to a linear one (sold separately in specialized stores). Then it will work if your TV set supports satellite cam-modules.

Will 60% properties be pretty? Better to set up does not come out, maybe trees and the adjoining house are in the way.

Not enough 60% of the property ((. But since you have already installed, try to start the preview without activation and look at the quality.

no, I still think my problem is in the antenna of a small diameter. according to the advice of the forum and professionals, I installed the sat703 cavel cable; the converter I installed according to the advice of the website is not very expensive, but as they say it is better than the regular GI-211 for two hundred and 30 rubles. Yesterday the whole evening there was no signal, so to speak. now in the morning there is a quality jumping from 30 to 100 percent no rain. oh so so so.

Galina, you figured it out. Are you convinced that the antenna is tuned accurately? Usually, it is precisely inaccurate antenna tuning that causes such problems.

good evening. why do I think to buy a larger plate, namely a long-focus one at 90cm. TV set with a cam module. in good weather the signal properties jump from 100 percent to zero. the image crumbles and quite often writes no signal. I go to the signal option, there is no signal at all. the 60cm plate is set up correctly. Now it is raining; there is no signal in general, practically the whole day. what's the matter actually. a larger plate may help. I live in Togliatti.

Galina, yes, we figured out what you want to do better quality signal, and a long-focus antenna, indeed, with other things being equal, will provide more stable reception. But there may be a discrepancy in something else (for example, with a faulty converter or a warped cable, replacing the antenna will not help). We advise you to read the article at this link and make sure that all the obstacles that are voiced there are resolved.

I'll hand it back to the store. Therefore, the cost was affordable two thousand nine hundred and ninety rubles, for a set.

Good day. I got a set of Mts satellite TV set-top box, model S2-3900, does not find a satellite, signals by zeros, I twisted the dish in all directions, insisted on the angle using the SatFinder application. Maybe the prefix is ​​defective.

Good day. This ability cannot be ruled out. As well as a converter malfunction.

after the transition to a new satellite, only 40 channels and twelve radios are received. I tried all the options - nothing helps ... I will probably have to part with MTS.

Before leaving, try to call tech support all the same. Maybe not all transponders have been added, for example, or some other problem to be solved.

Good day! I bought the whole set and nothing is configured even by annotation. At first, the remote control is not configured when the TV code is selected. I have a TOSHIBA TV set, model 37AV500PR. The codes for the remote control option are 25. Nothing comes out. When you turn on the TV set and set-top box, first the MTS TV splash screen is displayed, later the screen turns black and “No service” is written. Please tell me what is the problem.

Hello. This inscription means that the satellite signal is not received by the receiver: there is a discrepancy either in the antenna setting or in the cable.

tell me where you can buy a 90cm long-focus dish. or which cymbal models are telephoto.

Hello. Long focus antennas of different diameters are available from many manufacturers. When choosing an antenna, pay attention to the f / d ratio (f is the focal length, d is the antenna diameter), if it is 0.6 or more, the antenna is long-focus. Visually long-focus antennas are flatter, while short-focus antennas, on the contrary, are convex.

Long focus antenna models great amount, therefore, it is better for you to contact a satellite equipment store and ask the sellers what is in stock. But where to find such a store - we cannot give a hint, tk. you didn't write your own address.

is such a plate suitable for mts STV-0.9-1.10.8 St AUM SKN 600-900.

It does not matter which offset antenna is suitable, the only thing is that the diameter must be selected according to the signal strength in your region. And remember that larger antennas are more difficult to tune.

Good evening. I have a DCD 4404 HD set-top box, each time it is turned on, a full scan of all frequencies is performed and the previously deleted channels appear again. Is there any way to block this scan .......

Hello, unfortunately, this function cannot be removed. You do not have to turn off the set-top box (but only the TV set), then there will be no scanning.

good evening !! what could be the reason quite often the image-cubes are poured. The cymbal is configured. The converter is replaced by GI-211. Cable sat-703 from -cavel. Signal level 100%. Quality 90%. LG49UH619V TV set with cam-module. does it make sense to use a signal amplifier.

We cannot say remotely for sure. It may be worth changing the antenna to a long-focus one if you are convinced that the cable and converter are in order. Take a look here this article, it describes the possible actions to correct the situation, including the installation of the amplifier.

Hello! I cannot tune the antenna with the CAM module. I live in the village of Kazachinskoe, Irkutsk region. Your website is reporting: azimuth 218, mirror angle -7, converter 20 deg. No signal.

Hello! It is better to create a setting through the SatFinder application.

Hello. How to register in personal account... Send a link, if possible.

The answer to your question is on the page "Personal Account"

Something is not disclosed channels of funds in the account there .. what to do?

What does “no channels open” mean? What do you see on the display? What equipment do you have?

Hello, we wanted to connect the TV mts ourselves, turn it on, load up to 95% and write no service, what does this mean? No satellite signal?

Hello. Yes, “no service” means that the receiver is not receiving a signal.

how, HOW to set up the set-top box after the software, it is annoying to look at the dark screen. tell.

Victoria, tell me the model of the console?

Hello. I bought a LG TV set in it there is a DVB-S2 tuner And in the menu only the ABS-2 satellite, i.e. ABS-2A is not .. enter it manually, either. now all that remains is to wait for a firmware update with a new satellite. and if I enter the transponder eleven thousand nine hundred 20 in the settings for the ABS-2 satellite. will demonstrate or not.

Hello! Enter satellite data manually.

Hello! After switching to a new satellite, I can not do the channel tuning. TV set with CAM-module. I set all the required characteristics: transponder frequency -11920, symbol rate - 45000, polarization - vertical, network search - incl. Indicates: signal quality - 86%, Network name - SAT. I search for channels - channels 0! Nothing is found. There's no use in tech support! Only SMS with options are sent. They say: Call the tuner.

On the ancient satellite, I set up everything myself normally the first time. And here I fight for the 5th day. Nothing comes out. How else do you need to configure?

Hello. In this case, it is better to re-configure all channels, alternately adding all transponders.

Why are you silent ?? official representatives mts ?? I asked you a question dated October 22, 2017. It turns out that since October 18, 2017, in order to improve the property in bad weather, MTS is transferring broadcasting from the ABS-2 satellite to the ABC-2A satellite with a simultaneous frequency configuration. that is, the transponders have changed. I entered new transponders. both in the TV set and in the set-top box and it all worked.

The claim is not entirely clear. We wrote a whole article about reconfiguring to another satellite and there are links to it everywhere in the comments.

Hello, tell me the transponder number for the MTS receiver option, that is, everything that needs to be entered.

Hello. All information is contained in the article at this link.

After the option of the antenna to the satellite (according to a suitable azimuth, tilt of the "dish", the converter is turned to a suitable degree), the power and quality of the signal by zeros, the search for the signal does not give any result.

What could be the problem?

Hello. Several circumstances of this situation are described here.

Hello, I would like to find out when tuning to a satellite, it is absolutely necessary to activate a SIM card? That the signal was better?

Hello. No, activation has no effect on signal quality.

Hello. After the option of the antenna to the satellite (according to the appropriate azimuth, the inclination of the "dish", the converter is turned to a suitable degree), the inscription "NO SERVICE" appears on the TV display, this is the first thing. Signal strength and quality by zeros, signal searches are ineffective (both scales did not even budge), I try to catch the signal within a week. The neighbors who purchased the same set from the same dealer called the tuner, who did not even turn the antenna and without touching the receiver, turned on all the channels through a laptop (web) (the dealer and the tuner are familiar). Is it possible to protect the receiver with a password, so that later only the tuner (who is obviously in collusion with the dealer for the purpose of “divorce” on funds) can type "configure"? It's just that my case is not unique in our village (the same tuner arrives)

Hello. On the receiver, you can put a password for viewing certain channels, but “password-protected” reception of a signal from a satellite is unrealistic.

good day. I got a plate of mts and a cam module with a map from mts. and there is also a DS300A prefix. set the dish according to the annotation. but no signal. that is, the level and quality on TV through the prefix indicates zero percent. via telly the same thing. telly LG49UH619V to say that the cymbal is not configured correctly. I don’t think how we didn’t twist it. according to annotation and satellite information. whether the LUMAX LU-2115 converter can be defective. that is, we tried it through TV through the tuner. and from the prefix. level and quality zero. ... it may be necessary to insert a cam module with a sim card for a signal, otherwise we try without it in both cases .. I apologize for the messy writing. with the installation of the cymbals, I installed the tricolor more than once, no problem.

Good day. Check the polarization of the converter, it should be linear. For some reason, we did not find its technical properties on the web, so we cannot say whether it fits or not.

I got the MTS S2-3900 prefix. I came home, set up the dish, everything according to the annotation, and tried it with the application on the phone, and so, using the compass, but it does not catch the 1st channel, just as I didn’t try to turn it. I press search, it goes to 100%, and the inscription - there is no service in the middle of the dark screen. What could be the reason?

Such an inscription means that the signal is not being sent to the set-top box. The discrepancy can be both in the antenna (not only an incorrect setting, but also an obstacle in the direction of the satellite), and in the cable (check all its connections) or the converter (it may be faulty).

How long is the mts smart card activated?

Immediately after your request for equipment, several signals about its activation are sent off.

Hello. We are renting an apartment, because the equipment is not ours, there are questions.

We have two remotes:

1) from the TV (sony);

2) from the MTS prefix.

The TV remote control only needed ON and OFF. , and for the rest, use the console from the console. The spouse did not know this and pressed something else on the TV remote control (((. Now, nothing is shown from the set-top box, but a black screen with the number one in the upper right corner is burning. Please help me how to be.

Hello, reboot the box (turn off and on the power supply).

How to call professionals at home to install a TV.

How do I choose my own time zone? So that the programs go according to local time.

You cannot tune channels like this. There are several channels running in different time zones, they are found at the end of the channel list.

Hello, there was an announcement that there was a technical break from two in the morning until 10 in the morning. but until now does not indicate. Kazan, aircraft building region.

Hello, please read this article.

How to set up the program guide, so that when you switch channels, create what program is going on at this moment and will continue to go?

In general, this is how it works for deflot. Try to reset the prefix options to the factory ones.

Received TV: BBK 40LEM-1031 / FTS2C "R", 40 ″ and a set of MTS satellite TV set # 70.

The installation was carried out in the Metropolitan area. Of course, I could not tune the antenna myself, I called a local master.

Signal strength ninety%

Caught 200+ channels.

The master left said that this is the maximum that you can survive, call MTS, activate the card.

After activation, only channels from transponders are shown (11733 MHz | SR 40 three thousand | FEC 5/6 | Vertical)

All other channels are pouring, freezing, etc.

He called this master, he said that he had done everything and so it would not be possible to show more than one channel in the rain.

P.S. In the TV set, there was no satellite ABS-2, everything was scored manually. But I did not find where to drive the error (FEC), as well as the "Frequency of the reference / home transponder"

There is only an option to drive in all eight transponders and that's it.

Good day. By turning the converter around its axis, you can achieve the best signal properties. Difficulty in the rain, scattering of the figures into cubes occurs with inaccurate settings.

I got the MTS S2-3900 prefix. She hung up on me, I gave it right away, I re-flashed the software. I took it home, set up the dish, everything according to the annotation, and tried it with the application on the phone, and so, using the compass, but it doesn’t catch the 1st channel, just as I didn’t try to turn it. I press search, it goes to 100%, and the inscription - there is no service in the middle of the dark screen. What could be the reason?

Such an inscription means that the signal through the cable does not reach the set-top box (in case the antenna picks up the signal), or that the antenna is configured incorrectly.

Hello, the receiver from MTS S2-3900 sometimes, once every 10 minutes, reboots itself, or it happens more often. First it freezes, i.e. the remote control buttons do not respond and after a second it reboots and returns to the same channel. What could be the reason?

Hello! The reason is a receiver malfunction, it is necessary to take it to the MTS communication salon for diagnostics.

I have a Rolsen RDB-702 satellite receiver. How to tune 5 degrees on MTS 70? I live in Samara. I connected the receiver, inserted the cable from the plate. Added satellite 075.0е, with options "type 09750 \ 10600, power 13 \ 18, 22khz auto" Search Blind Scan. Doesn't find anything. I insert the map into the TV set, everything points to it. That is, the dish is configured and the module is activated. What am I doing wrong and how should I? Help pls ..

Hello! Unfortunately, we cannot help with setting up other receivers, for you you need to contact the technical support of the receiver manufacturer.

Hello Tell me if a plate and a convector from TelekartR TV will fit.

Yes, they do, but you will need to turn the antenna to another satellite.

Good evening. How to build channels in a sequence that suits me, on the very first MTS receiver (without a name, for an exchange for a rainbow TV) Before the update, everything was simple and clear, but now the update has come and I can't configure everything.

Hello. Throw off options to industrial, the discrepancy should disappear.

how can i change the time zone in digital tv.

In cable digital?

how to call a specialist in setting up satellite television?

In which town do you need customization?

Hello. Can you tell me if an antenna and a converter from a rainbow TV are suitable for your television?

Hello! Yes, they do.

Can't set up satellite TV. Gives out the inscription "overcurrent on the antenna". What is it all the same? and what to do?

In most cases, this means that a short circuit has come out. Visually inspect all cable and connections. It can also happen due to incorrect installation of the F-connectors.

I can't configure the CAM module, I installed the dish according to the program, but we can't configure it on the TV set itself, help me. TV model LG 32LB57? thanks.

Use our annotation. You can also contact the hot line MTS or LG technical support.

Please send a detailed annotation on setting up your DSD4614i satellite TV receiver.

This annotation is available on our website under the Documents section.

Good day! Tell me how to set the time on the console?

Good! The set-top box receives information about the date and time from the satellite signal, i.e. You cannot change these options without the help of others.

Nice day. Please answer my questions:

1. When installing a satellite TV set, is it possible to use an existing ordinary TV cable already wired around the house, or is it necessary to lay it again?

2.How to organize watching satellite TV mts on several TVs in the house?

1 - yes, you can, if it is a modern coaxial cable. Cable dividers, if installed, must comply with satellite TV standards.

2 - you can use either a converter with 2 outputs, or a splitter on the cable. You can read more about connecting multiple TVs here.

Every time, in bad weather, you have to call a cymbal tune-up wizard ... All this is paid and not cheap. Therefore, your television becomes gold. What about the service.

Judging by your words, the master tunes the antenna every time, which means that it is loosely fixed and changes the angle of rotation due to the wind. We can recommend either to fix the antenna more firmly, or, if this is unrealistic, to purchase a lighter and more wind-resistant perforated or duralumin antenna.

Good day! Is the convector ap8-xts2e-fs suitable?

Hello! Yes, it will do.

Good day IS IT NECESSARY AFTER INSTALLING THE ANTENNA TO GO TO THE MTS SALON TO CONCLUDE THE CONTRACT, THE EQUIPMENT WAS PURCHASED AT THE POINT WHEN PURCHASING THE TELECA THANKS.

If you want to have a paper version of the contract, then yes, you can contact the MTS communication salon. But you can also enter your data in this form, and after which the contract will be considered concluded, its number will be sent to you by SMS.

Hello. Tell me what version of CAM module Ci or Ci +? And is the antenna tuned to the Tricolor suitable?

We need a CI + interface. The antenna itself does not need to be changed, but it is useful to reconfigure it and change the converter.

I would like to ask you to send the satellite TV options for the tf-led43s27t2 TV set.