Until September 1, 1939, the French did not have time to form tank divisions. The formation of the 3rd light mechanized division advanced the furthest, and organizational measures began to form the fourth. Eight infantry divisions were motorized (1st, 3rd, 5th, 9th, 10th, 12th, 15th and 25th). Trucks were used to transport infantry. Otherwise, the tactics of motorized infantry divisions were no different from those of conventional infantry.

Motorized infantry divisions became part of army corps. And again, for the umpteenth time, the French made a gross mistake by introducing two conventional infantry divisions into the army corps along with the motorized infantry. Thus, the entire advantage of motorized infantry was nullified. The French had to spend enormous amounts of money to somehow bring up the infantry divisions to the level of mobility of motorized infantry divisions.

In January 1940, the formation of the 1st and 2nd Panzer Divisions was finally completed. Until March, the 3rd Panzer Division was formed. The last - the 4th Panzer Division - completed its formation when fighting already started.

According to the state, each division was to have a semi-brigade (Demi-Brigade) of medium tanks (2 battalions of Char B1 tanks - 60 vehicles) and a semi-brigade of light tanks (2 battalions of H-39 cavalry tanks - 90 vehicles). In addition, the tank division included a motorized infantry battalion (equipped with 20 armored vehicles), 2 divisions of 105-mm howitzers, a battery of 47-mm anti-tank guns and a battery of 25-mm anti-aircraft guns.

In total, as of May 10, 1940, the French army had 49 battalions of light tanks for direct infantry support, 3 light mechanized divisions and 3 tank divisions. Three battalions of D1 tanks, one battalion of H-35 tanks were deployed in North Africa, and a battalion of R-35 tanks was based in Levanto. Light tank battalions were part of larger units: brigades, regiments and tank groups. There were 3 tank brigades (2nd, 4th and 5th) and 14 tank regiments (501st, 502nd, 503rd, 504th, 505th, 506th, 507th, 508th, 509th, 510th, 511th, 512th, 513th and 514th). The regiments and brigades were disbanded in March 1940.

Tank brigades usually consisted of two regiments, and regiments of two battalions. Each battalion consisted of about 50 vehicles.

Before the start of the offensive, the Nazis concentrated the main forces on the northern flank. Between the sea coast and Mosa, Army Group "B" was to advance, under the command of Colonel General Fedor von Bock (von Bock). Army Group "B" consisted of two armies - the 6th and 18th - a total of 29 divisions, including three armored and one motorized. These forces were supposed to tie up the Allied troops and divert them from the direction of the main attack.

The main blow was delivered by Army Group A, under the command of Gerd von Rundstedt (von Rundstedt), which united the 4th, 12th and 16th armies - a total of 45 divisions, including 7 tank and 3 motorized. The troops of Army Group A were to strike through Belgian territory south of the Liège-Charleroi line in the direction of Meyen-Saint-Quentin along a front 170 km wide - from Regen to the point where the borders of Germany, Luxembourg and France converge. The goal of Army Group A was to seize the crossings across the Mosa between Dena and Sedan at lightning speed, which made it possible to make a breakthrough at the junction of the 9th and 12th French armies and reach the rear of the Maginot line in the direction of the mouth of the Somme River.

On the southern flank between the Moselle and the Swiss border, Army Group C, led by General Wilhelm Ritter von Leeb, advanced. The task of this Army Group was simply to pin down as many enemy forces as possible.

In total, the Germans fielded 10 tank divisions in the French campaign. The Nazis had 523 Pz. Kpfw. I, 955 tanks Pz. Kpfw. II, 349 tanks Pz. Kpfw. III, 278 tanks Pz. Kpfw. IV, 106 tanks Pz. Kpfw. 35(t) and 228 tanks Pz. Kpfw. 38(t). In addition, the Germans had 96 command tanks kl. Pz. BfWg. I, created on the basis of Pz. Kpfw. I and 39 command tanks Pz. BfWg. III on the chassis of the tank Pz. Kpfw. III. Generally german tanks inferior to the French in the power of weapons and the thickness of the armor. Tanks Pz. Kpfw. I, armed with two machine guns, did not pose any threat to the French armored vehicles. Tanks Pz. Kpfw. II, armed with a 20 mm cannon, could only inflict damage on French vehicles in unusually favorable conditions, for example, from point-blank ambush. Tanks Pz. Kpfw. III and Czech Pz. Kfw. 38(t), armed with a 37 mm cannon (Pz. Kpfw. III, armed with a 50 mm gun appeared with the Germans when the fighting was in full swing) were approximately equal to the French R-35, R-39, H-35 and H-39. The Nazis had no analogue to the French Char B1 and Somua S-35. The Germans could fight these tanks in only one way: first by breaking the caterpillar, and then, going into the flank, hit the tank from the side. The only worthy enemy for medium French tanks were Pz. Kpfw. IV. However, the fate of the campaign was not decided performance characteristics tanks. Tactics and military doctrine played a decisive role - here the advantage of the Germans over the French was overwhelming. It was only through the bitter experience of the first month of the campaign that the French command realized the magnitude of the mistake that had been made during the interwar twenty years.

Based on intelligence data, the commander of the northeastern front, French General Joseph Georges (Georges), suggested that the Germans would strike the main blow with the right flank north of Liege and Namur through Belgium, in other words, the Germans decided to repeat the "Schlieffen plan" of the 1st World War war. In order to frustrate the enemy's plans, the allies decided to occupy defensive lines between Namur and Antwerp, along the Dil River, and give the Germans a general battle in Belgium, on the borders of which most of the German motorized infantry and tanks were concentrated. This maneuver was to be carried out by the troops of the French 1st Army Group (1st, 2nd and 7th armies), led by General Gaston Henri Billote, as well as the British expeditionary force of General John Gort (Gort).

The French occupied the defense so that the civilian population suffered as little as possible. The French were going to create a network of fortified points saturated with anti-tank weapons. According to the allies, this was supposed to force the enemy to get bogged down in battles, but due to lack of time, the French and British did not have time to implement their plan. The commander of the 1st mechanized cavalry corps (2nd and 3rd light mechanized divisions), General Prua (Proiux) wrote in his memoirs:

“On the morning of May 11, I arrived at Gamble and inspected the positions being equipped. Surprisingly: not the slightest trace of fortification work around the city - the key point of the entire operation. Only 8-9 km to the east did I find the first elements of anti-tank defense, but they did not form a continuous line and therefore had no real combat value. With confusion, I thought that the army should have carried out reconnaissance first and then started earthworks. However, the enemy did not give us time!”

The French leadership, which adopted the concept of a passive strategy, did not dare to launch preventive or counterattacks on the enemy, but simply tried to stop the Nazi offensive. According to the French command, the war was to quickly turn into a positional form. Therefore, the German troops did not meet with a proper rebuff and were able to quickly develop an offensive deep into France and reach the shores of the English Channel.

Of the three French light divisions, one (1st light mechanized division) was given to the 1st Army. The other two were merged into the 1st Mechanized Cavalry Corps, which we have already mentioned. All these forces were assembled on the Flanders front and were waiting for the enemy to attack.

General Proix's corps made contact with the German XVI Panzer Corps in the Gambloux and Namur area. On May 12-13, in the suburbs of Namur, French forces with 74 S-35 tanks, 87 H-35 tanks and 40 AMR tanks fought German tanks from the 3rd and 4th Panzer Divisions. In an unequal battle, the French managed to burn 64 German tanks. The corps delayed the advance of the enemy for two days, and then was disbanded. The divisions of the corps were distributed among the infantry corps.

The commanders of these corps, in turn, divided the light divisions into parts and reinforced the infantry divisions with these parts. Shattered mechanized parts could no longer play prominent role in the war. When the French command realized this mistake, it was already too late - it was already impossible to assemble parts of two divisions. Only by May 20, with great difficulty, was it possible to recreate the 3rd Mechanized Light Division bit by bit.

While the corps of General Proix was desperately trying to hold back the advance of the enemy near Gamble, nearby - near Crean - the 2nd cuirassier regiment of the French fought the German 35th tank regiment of the 4th tank division. In the battle, the French lost 11 H-39 tanks.

On the Belgian border, the French concentrated all three of their panzer divisions. Two of them were not fully equipped and together they had 136 tanks. The third division had a staffing strength of 180 vehicles.

Meanwhile, motorized units from Army Group A passed the Ardennes, which were considered impassable, and crossed the Mosa between Givet and Sedan from the march. Thus, the Germans entered the rear of the Allied troops in Flanders. The entire Allied defense plan was a complete fiasco. The Anglo-French troops had to start a retreat.

To contain the enemy's advance, the French command decided to use its mechanized units. On May 14, 1940, the 1st Panzer Division, which was part of the French 9th, was to attack the German troops that had crossed the Mosa. On the evening of May 13, the division took up its original positions ... and remained there due to lack of fuel! The delay allowed the reconnaissance of the German XIX motorized corps (1st, 2nd and 10th Panzer divisions) to detect the French. On May 14, the Germans were the first to strike. Near Bulson, the French 1st Panzer Division lost 20 tanks. Things were even worse near Chemery, where 50 French tanks were left to burn. Many tanks, standing without fuel, destroyed the crews. The French had one thing to do - retreat. We had to retreat under continuous German air raids. By May 16, the French 1st Panzer Division already had only 17 combat-ready vehicles. On the night of May 16-17, these crumbs were also lost. So already a week after the start of hostilities and just three days after arriving at the front line, the 1st Panzer Division ceased to exist!

The fate of the 2nd Panzer Division was a little better. On May 14, 1940, the division set out from Champagne, with tanks being transferred by rail, and wheeled vehicles moving under their own power. Already on May 15, parts of the division were separated by a German wedge. From that moment on, the 2nd Panzer Division also did not exist as a single tactical formation! The front commander ordered the tanks of the 2nd division to be unloaded from the platforms and placed in small groups in the area of ​​crossings across the Oise River. The task of the tanks was to delay the German units crossing the river. On May 15, units of General Reinhardt's XXXXI corps crossed the river. The French tanks supporting the infantry fought bravely, but were all put out of action. The German offensive continued successfully.

On May 14, 1940, the French 3rd Panzer Division was placed at the disposal of the commander of the 2nd Army. Like the 1st Panzer, the 3rd Panzer Division was ordered to counterattack the enemy in the Moza area, but did not follow the order. The delay occurred for two reasons: firstly, the division was on the defensive, so it had to regroup its forces to go on the offensive; secondly, the command order was inaccurate and did not contain specific indications of the place of attack and possible enemy forces. Therefore, the division remained on the defensive lines and gradually the Germans drove it to the Oise.

On May 11, 1940, Colonel Charles de Gaulle was appointed commander of the 4th Panzer Division. Despite the fact that the division had not yet completed its formation, it was thrown into battle. In total, the division had 215 tanks (120 R-35s, 45 D2s and 50 B1bis). The only infantry unit of the division was a motorized infantry battalion transported on buses! There were practically no radio stations in the division, and orders were delivered to the units by cyclists! The artillery of the division consisted of several parts of the reserve. supply services and Maintenance practically did not exist. In principle, this unit can hardly even be called a division - it was a motley mixture of disparate units and subunits that happened to be together. Despite everything, the young division commander was able to make a formidable fighting force out of this booth.

On May 16, 1940, the division of General de Gaulle (on May 14 he was promoted to brigadier general) attacked the southern flank of the German wedge (1st, 2nd and 6th tank divisions) in the Montcornet area.

Realizing that the enemy had a numerical superiority, de Gaulle acted very carefully and tried only to delay the advance of the enemy.

The 49th Panzer Battalion was sent out to reconnoiter Montcornet and tried to enter the city from the southwest. With a swift attack, the French dispersed the outposts of the German 10th Panzer Division. However, the Germans managed to surround the battalion, all of whose personnel were captured. The 4th Panzer Division continued to adhere to this "cavalry charge" tactic, striking where it was least expected. On May 19, several tanks of de Gaulle's division attacked the headquarters of the XIX motorized corps of the Germans, located in the forest of Olno. The headquarters was covered only by a battery of 20-mm anti-aircraft guns. The battle lasted several hours, despite the desperate efforts of the French, the Germans were able to hold their positions.

The tank divisions of the Nazis continued to roll forward uncontrollably. Nothing and no one could stop their progress. By May 20, 1940, the ticks around the Allied forces in Flanders had completely closed. The French and British had to either fight their way to their own or retreat to Dunkirk or Calais. On May 21, 98 British tanks from 4 and 7 RTR were ordered to attack the flank of the German troops near Arras. The British attack was covered by 70 French S-35s from the 3rd Mechanized Light Division. The attackers were quickly successful. The 1st Battalion of the 6th Motorized Infantry Regiment of the 7th Panzer Division of the Germans was dispersed. To close the gap at the front, the Germans transferred the 25th Tank Regiment there. Having lost 25 vehicles, the Germans were still able to hold their positions.

After this defeat, the Allies had only one thing left - evacuation to England. Boulogne and Calais were lost, the only port remaining in the hands of the British and French was Dunkirk. It was there that the Allied troops retreated. Completely demoralized, pressed to the ground by continuous German air raids, this grouping no longer participated in the campaign.

At the end of May, the 4th Panzer Division of General de Gaulle once again declared itself. Its already badly battered forces hit the German flank in the Abbeville area. The French went on the counterattack twice - on May 27 and 28. However, the Germans were able to hold their positions, inflicting heavy losses on the French.

Already on May 20, 1940, the British began to send equipment to Dunkirk necessary for the evacuation. On May 26, the British command put the Dynamo plan into action. Despite the constant attacks of the German infantry and the raids of the Luftwaffe bombers, the British in an organized manner managed to take out from the continent the entire personnel of the Expeditionary Force and a significant part of the French troops that fell into the bag. But since the Battle of Flanders was lost, the Allies lost more than half of their troops there.

Before the start of the second stage of the campaign, which was supposed to decide the fate of France, the French still had quite impressive forces: 61 divisions of their own, 2 Polish divisions and 2 British divisions. More than 1,200 tanks remained on the line, but these tanks were divided into small groups and assigned to different units.

These forces were supposed to save France, relying on the line of defense over the Somme. Since there was no Maginot Line here, the French command organized a chain of improvised anti-tank obstacles - "hedgehogs" in this sector. Behind the hedgehogs are infantry, artillery and tanks. But unfortunately, the “hedgehogs” did not form a continuous line, and units of the Wehrmacht broke through between them. And the French did not have at hand mobile units capable of quickly being in a threatened point.

On June 5, the day after the occupation of Dunkirk, Army Group B went on the attack. The purpose of the offensive was to capture the southern bank of the Somme. The tank formations of Generals Hoth and Kleist went into the breakthrough, attacking the defensive formations of the 7th and 10th French Armies.

On June 10, 1940, in the area of ​​Avanson and Tagnon, over the Rethorn River, the newly formed XXXIX Motorized Corps of General Guderian went on the attack. Moving across the open countryside, the German tanks encountered virtually no resistance from the French. The German units immediately crossed Rethorn in the Neuflies area. Shortly after noon, the Nazis reached Gennivil. At this moment, units of the French 3rd Panzer and 7th Infantry Divisions went on the counterattack. To the south of the city there was an oncoming tank battle that lasted two hours. In this battle, the Germans suffered heavy losses, the aggressors had a particularly hard time when the French Char B1bis medium tanks entered into action, the armor of which kept hits from armor-piercing shells of 20 and 37 mm caliber. However, the numerical superiority was on the side of the Nazis, and despite heavy losses, they were able to push the French back to La Neuville. In the evening, the battle resumed with new force, this time south of Gennevil. Again, French tanks from the divisions mentioned above went on the attack. The French planned to take Perth by storm, but the Germans were once again able to hold their ground.

On June 11, the German 1st Panzer Division attacked the French in the La Neuville area and was able to break through the enemy defenses. Only over the Suip River did the French attempt to launch a counteroffensive. 50 French tanks from the 3rd Panzer Division, supported by soldiers from the 3rd Panzer Division, tried to close the gap in the defense. infantry division. But this attack also failed.

On June 12, the Germans widened the gap in the French defenses and separated the Allied western flank from the main forces defending Alsace, Lorraine and the Maginot Line.

On June 14, General von Leeb's Army Group C went on the offensive, the 1st Army of which struck from the Saarbrücken region to the south, and the 7th Army crossed the Rhine, occupied Colmar and met with Guderian's tanks in the Vosges region.

On the same day, the Germans entered Paris without a fight. Three days later, Marshal Pétain announced on the radio a request for a truce. This performance finally broke the morale French army. Only a few units continued to resist. The French, who at first did not want to die for Gdansk, as it turned out, were not at all eager to die for Paris. On June 22, an armistice was signed. The French army was completely defeated, the campaign in the west came to an end.

In this war, the tank units of the French army were completely destroyed. It turned out that not the number of tanks, but the tactics of their use decide the outcome of the battle. The French were not able to operate as effectively with large tank formations as their enemy did. Instead of gathering their tanks into one powerful fist, the French sprayed them all over the front. Very rarely did the French try to use tanks as their main fighting force in the offensive, and if they did, they used too few tanks. At best, one incomplete tank division went on the attack. As a result, the attack choked, stumbling into the defense of the enemy, equipped with tanks and anti-tank guns. Often such attacks ended in the complete defeat of the attacking side. Quite often, the French tried to use tanks on terrain that was completely unsuitable for the use of armored vehicles. The only motive for such actions was the desire to show the infantry that they were "not alone on the battlefield." As a result, in the main directions of attack, the Nazis had a colossal superiority in tanks. The French tried to transfer one or two tank divisions to the threatened sector of the front, but as a rule it was already too late.

The creation of armored vehicles in France went on even during the occupation of the country by the Nazi invaders. The liberation of the territory of France marked for her not only a victory, but also a difficult process of restoration and creation of her own army. Ours begins with the transition tank ARL-44. Start of development - 38 years. This was new type tanks based on the B1 chassis. According to the project, the tank was to receive a turret of a new type of design and a 75 mm long-barreled gun. By the beginning of the war, work on the creation of the tank was at the level of development. But even during the occupation, design work on the tank was carried out no less successfully than before it. And when France was liberated, the first sample of the new tank was immediately put into production. In series new tank went in 46, which for France was undoubtedly a feat of industry, given the fact of a five-year occupation. Due to various reasons, the tank became a kind of transitional model and enters service as the ARL - 44. The French military wanted to get 300 units of such tanks, but only 60 vehicles of this series were built. They were adopted by the 503rd Tank Regiment.

The tanks were manufactured by Renault and FAMH Schneider, the latter producing a new type of turret. From the "B1" the new tank got a morally obsolete suspension and caterpillar tracks. In terms of speed characteristics, the tank turned out to be the slowest post-war tank and had top speed traffic 37 km/h. But the engine and hull were new developments, the armor plates on the hull were placed at an angle of 45 degrees, which gave the frontal armor the equivalent of 17 centimeters of normally installed armor. The turret of the tank was the most modern of the new machine. The disadvantage of the tower is the poor quality of the connecting seams, and the French industry was simply unable to make such a tower completely cast. A 90 mm Schneider gun was installed on the tower. In general, the ARL-44 turned out to be an “unsuccessful” tank, but do not forget that the tank was a transitional model, it had elements of both new and old tanks. And the task of the tank was essentially "non-military" - the tank, with its production, revived French tank building from the ashes, for which many thanks to him.

The next tank developed by French specialists was the AMX 12t. This is the younger brother of the future French AMX 13. Already from the name it is clear that the weight of this tank was 12 tons. Chassis younger brother had a rear track roller, which was at the same time a sloth. As it turned out, this configuration of the rollers was unreliable and caused constant problems with the tension of the tracks. This undercarriage with a modified configuration of the rollers, where the sloth became a separate element of the undercarriage, which led to an elongation of the tank hull, became the basis for the creation of the legend of the French tank builders "AMX-13". The AMX 12t turret was the progenitor of the AMX-13 tank turret. The tank, according to the project, was equipped with an automatic loader.

46 year. The design phase of the new tank has been completed. According to the requirements, the AMX 13 had a light weight for movement by aircraft in support of paratroopers. The new AMX 13 gets a torsion bar suspension, the engine is located in front and on the right, while the driver-mechanic was located on the left. The main feature that makes this tank unique is the oscillating turret. The turret was equipped with a top-mounted gun. With vertical aiming of the gun, only the upper part itself was used. The tower was installed in the aft part of the hull, and it housed the rest of the crew of the armored vehicle - the commander and gunner. The 75 mm gun of the tank was designed from the German 7.5 cm KwK 42 L/70 gun, which was used on the Panthers and was provided with a wide range of shells. The tower received a rather interesting automatic drum-type reloading system - 2 drums, each with 6 shells. The drums were in the rear of the tower. The ammunition load of 12 ammunition allowed the tank to fire very quickly, but as soon as the ammunition in the drums ran out, the tank had to take cover and reload the drums manually, outside the vehicle.

Serial production of the AMX 13 began in 1952, for its production the facilities of the Atelier de Construction Roanne were used. For almost 30 years he entered service with the French Armed Forces. Several hundred units of the AMX 13 are still serving in French tank units. One of the most massive European tanks, delivered to 25 states. Today, there are about a hundred modifications of the tank. All kinds of armored vehicles are created on its basis: self-propelled guns, air defense systems, armored personnel carriers and self-propelled ATGMs.

AMX-13 / 90- is the first modification of the main AMX 13. Entered service in the early 60s. The main difference is the installed 90 mm gun, equipped with a casing and a muzzle brake. Ammunition was slightly reduced - now the tank gun had 32 ammunition, of which 12 were installed in the drum magazine. The gun could fire high-explosive, armor-piercing, cumulative, sub-caliber shells.

Batignolles-Chatillon 25t is a design modification of the main AMX 13. Only two units of this modification were created. To improve survivability, vehicles are increased in size and given additional armor. These and several other changes in total gave the weight of the tank - 25 tons. According to the project, the tank team consisted of 4 people, the design speed of this modification was 65 km / h.

"Lorraine 40t" was created in pursuit of such monsters as the Soviet IS-2 -3 and the German "Tiger II". Of course, the tank could not catch up with these outstanding tanks either in terms of armor or mass, and, probably, installing 100 mm, and then 120 mm guns was a kind of attempt to get closer to them. But all projects of such tanks either remained on paper or were released in limited quantities. All projects in this series used the German Maybach as a remote control. "Lorraine 40t" were released in 2 prototypes. In fact, this is a somewhat lightweight "AMX-50". Were present in the decision of the tank and distinctive features: turret located in the bow of the tank, and "pike nose" - similar to the IS-3. Rubber tires were also used for the road wheels, which gave the tank additional cushioning.

"M4" - the first model of a heavy tank. In order to somehow catch up with the USSR and Germany in the creation of heavy tanks, French designers begin building their own heavy tank. The first modification is called "M4" or project 141. This model practically copied the German Tiger. The undercarriage received small-linked caterpillars and “chessboard” track rollers, a torsion-type suspension with hydraulic shock absorption. The ground clearance of the tank could be changed up to 100 mm. The difference from the German tiger - the transmission and drive rollers were stern. According to the design of the tank, it was supposed to weigh about 30 tons, but in practice this would have to reduce the armor to 3 centimeters. It looked quite ridiculous against the background of the "Tiger" and IS. The armor is increased to 9 centimeters and set at optimal angles, so the weight of the vehicle has increased significantly compared to the design. The tank received a 90 mm Schneider in a classic turret and a 7.62 mm machine gun. The team of the car is five people. This model was not released even in the prototype, as a decision was made to replace the classic turret with a new one from FAMH

"AMH-50 - 100 mm" - serial heavy tank. The main feature - due to the parallel development of the AMX-50 and AMX-13, they have a great external resemblance to the latter.
49 year. Two units of the AMX-50 - 100 mm tank are being produced. 51 years old - the tank is in service with the French Armed Forces in a small series. The tank turned out to be very good and compares favorably with the American and British counterparts. But due to the constant lack of funds, "AMX-50 - 100 mm" did not become bulk tank. From the layout - the MTO was in the stern of the hull, the driver-mechanic with an assistant were in the control department, the vehicle commander was located in the turret to the left of the gun, the gunner to the right. The body of the cast type is made with optimal placement of the frontal armor at an angle, the thickness of the frontal and upper side armor plates is 11 centimeters. The nose-to-side transition is made thanks to beveled surfaces. It differs from the M4 project in additional rollers (5 external and 4 internal types). The machine gun from the front sheet is replaced by a machine gun coaxial with the gun. In addition, the tower part received an autonomous anti-aircraft installation- two 7.62-mm machine guns. The turret of the pumping type was developed by FAMH. Until the year 50, a 90 mm gun was installed in it, then a 100 mm gun was placed in a slightly modified tower. The rest of the turret design corresponds to the design of the AMX-13 turret. DU - petrol Maybach "HL 295" or engine "Saurer" diesel type. The designers expected that the use of engines with a capacity of 1000 hp would make it possible for the tank to acquire a speed of about 60 km / h. But as time has shown, the tank could not overcome the bar of 55 km/h.

"AMX-65t" - the Char de 65t tank - an advanced project for a heavy tank. The beginning of the main developments - 50 years. Suspension chess type, four-row arrangement of rollers. Frontal armor of the "pike nose" type similar to the Soviet IS-3 with a smaller inclined angle. The rest is a copy of the Royal Tiger. According to the project DU - 1000 strong Maybach engine. Possible armament- 100 mm anti-aircraft gun and machine gun.

"AMX-50 - 120 mm" - a heavy tank. Had three modifications 53, 55 and 58 years. French "competitor" of the Soviet IS-3. The frontal part is made, like that of a competitor, - according to the "pike nose" type. Modification of 53 years old had a classic-type turret with a 120-mm caliber gun. But the design turned out to be inconvenient. Modification 55 years- a tower of a pumping type with a 20-mm cannon paired with a 120 mm gun to destroy lightly armored vehicles. Significantly reinforced frontal armor, almost twice. This leads to a serious increase in weight: up to 64 tons against the previous 59 tons. The military department did not like this modification due to the increased weight. Modification 58 years."Lightweight" up to 57.8 tons modification "AMH-50 - 120 mm". It had a cast hull and rounded frontal armor. It was planned to use a thousand-strong Maybach as a remote control. However, the engine did not live up to expectations: out of the declared 1.2 thousand horses, the engine did not even give 850 hp. The use of a 120 mm gun made reloading inconvenient, and it was difficult for one or two people to move the ammunition from the gun. The team of the car was 4 people, and although the fourth member of the crew was listed as a radio operator, he was actually reloading. The tank was not built due to the appearance of HEAT shells, the armor given to such shells was a weak hindrance. The project is curtailed, but not forgotten. The developments will be used in the development of the project "OBT AMX-30"

Not only tanks
The AMX 105 AM or M-51 is the first self-propelled vehicle based on the AMX-13, a self-propelled 105 mm howitzer. The first sample was created in the year 50. The first serial self-propelled guns joined the ranks of the armed forces of France in 52. The self-propelled guns had a fixed, shifted to the stern, open cabin. A 105 mm Mk61 of the 50th model was installed in the wheelhouse. The gun had a muzzle brake. A 7.62 mm anti-aircraft machine gun was also placed there. Some AMX 105 AM self-propelled guns were armed with an additional 7.5 mm machine gun, which was installed in a turret with circular rotation. The main disadvantage is the slow aiming at the next target. Ammunition 56 ammunition, which included armor-piercing shells. The range of defeat with high-explosive ammunition is 15 thousand meters. The barrel was produced in 23 and 30 calibers, it was provided with a two-chamber muzzle brake. To control the fire, the AMX 105 AM self-propelled guns were equipped with a 6x sight and a 4x goniometer. These self-propelled guns were exported - they were used by Morocco, Israel and the Netherlands.

"AMH-13 F3 AM" - the first European post-war self-propelled guns. Adopted in the 60s. The self-propelled guns had a 155 mm caliber gun, 33 calibers long and a range of up to 25 kilometers. Rate of fire - 3 rds / min. "AMX-13 F3 AM" did not take ammunition with it, it was carried by a truck for it. Ammunition - 25 shells. The truck also transported 8 people - the ACS team. The very first "AMX-13 F3 AM" had a gasoline 8-cylinder engine with liquid cooling "Sofam Model SGxb.". The latest self-propelled guns had a 6-cylinder diesel engine liquid-cooled "Detroit Diesel 6V-53T". The diesel engine was more powerful than the gasoline engine and allowed the self-propelled guns to move 400 kilometers at a speed of 60 km / h.

"BATIGNOLLES-CHATILLON 155mm" self-propelled gun project. The main idea is to install a rotating type tower. The beginning of work on the creation of a sample - 55 years. The tower was completed in 1958. In 1959, the project was abandoned, the prototype of the self-propelled guns was not built. According to the project, the speed is 62 km/h, the weight is 34.3 tons, the team consists of 6 people.

"Lorraine 155" - self-propelled guns of types 50 and 51. The basis of the project is the base "Lorraine 40t" with the installation of a 155 mm howitzer gun. The main idea is the placement of the casemate part. Initially, on the first sample, it was located in the center of the ACS, on the next sample, it shifted to the bow of the ACS. Having a chassis with rubberized rollers made the self-propelled guns an interesting option to use. But in 55, the project was closed in favor of another ACS project "BATIGNOLLES-CHATILLON". Basic data: weight - 30.3 tons, crew - 5 people, travel speed - up to 62 km / h. The armament of the self-propelled guns is a 155 mm howitzer and a 20 mm cannon paired with it.

"AMX AC de 120" is the first project of a self-propelled gun mount based on the "M4" model of 46. Received a "chess" suspension and cabin in the bow. Outwardly, it resembled the German "JagdPanther". Design data: ACS weight - 34 tons, armor - 30/20 mm, crew - 4 people. Armament: 120 mm "Schneider" and a turret machine gun to the right of the wheelhouse. DU Maybach "HL 295" with a capacity of 1.2 thousand hp "AMX AC de 120" - the second project of a self-propelled gun mount based on the "M4" model 48. The main change is the cabin design. The silhouette of the car is changing: it becomes noticeably lower. Now the ACS has become similar to the "JagdPzIV". The armament has changed: the cabin of the self-propelled guns received a 20 mm "MG 151" turret, the feed of the self-propelled guns two 20 mm "MG 151".

And the last project reviewed is the AMX-50 Foch. Self-propelled gun mount based on the "AMX-50", receives a 120 mm gun. The outlines of the self-propelled guns resembled the German "JagdPanther". There was a machine-gun turret with a Reibel ZP on a remote control. The commander's tower was provided with a rangefinder. The ACS driver observed the situation through the available periscope. The main purpose is to support 100 mm tanks, destroy the most dangerous armored vehicles of the enemy. After successful tests in 51, a small number goes into service with the French Armed Forces. After, with the standardization of weapons of NATO members, self-propelled guns are removed from the assembly line and in 52 the project is closed in favor of the tank project “creating AMX-50-120”.

Tank building in our time is one of the leading areas in military affairs. Many European powers, including France, have always been famous for the development of armored vehicles. It is this country that is considered one of those states that can be safely reckoned among the ancestors of the armored forces. Therefore, in this article a detailed review of French tanks will be made, an analysis of models and the history of their development will be indicated.

background

Everyone knows that the construction of tanks as such began during the First World War. France was the second country to start using tanks on the battlefield.

The very first French tank was completely ready in September 1916. Its creator was J. Etienne, who, in fact, is considered the founding father of French tank building. This officer was the chief of staff of the artillery regiment. He perfectly understood how the situation at the front could be changed, and therefore he thought through the breakthrough of the enemy’s first line of defense precisely with the help of tracked vehicles. After that, in the occupied territory, he planned to install artillery and suppress enemy resistance already from this position. An important remark should be made here: armored vehicles, which we call tanks, were called "assault artillery tractors" by the French in those days.

Start of production

The senior command staff of France, like most military commanders of other countries of that time, was extremely wary and skeptical about the idea of ​​building a tank. However, Etienne was persistent and had the support of General Joff, thanks to which permission was obtained to build a prototype. In those years, the Renault company was the leader in mechanical engineering. It was to her that Etienne offered to open a new era of armored vehicles. But the company's management was forced to refuse, citing the fact that they have no experience with tracked vehicles.

In this regard, the French tank was entrusted to build the Schneider company, which was the largest manufacturer of various weapons and had experience in booking the Holt tractor. As a result, at the beginning of 1916, the company received an order for 400 tanks, which later received the name CA1 (“Schneider”).

Features of the first armored vehicle

Since no specific tank concept was announced, France received two different versions of the tanks, both of which were based on the caterpillar tractor model. In comparison with British armored vehicles, the French tank did not have tracks covering the entire hull around the perimeter. They were located on the sides and directly under the frame. The chassis was sprung, which made it easy to control the machine. In addition, this design provided comfort to the crew. However, the front of the car body hung over the tracks, and therefore any vertical obstacle in the way became insurmountable.

Tank Louis Renault

After it became clear that tank building - promising direction, Etienne again turned to Renault. This time, the officer was already able to clearly formulate the task for the manufacturer - to create light tank with a small silhouette and minimal vulnerability, the main function of which would be to accompany the infantry during the battle. As a result, French light tanks were created - Renault FT.

New generation technology

The Renault FT-17 tank is considered the first tank model to have a classic layout (the engine compartment was located at the rear, the fighting compartment was in the very center, and the control compartment was in front), and there was also a tower capable of rotating 360 degrees.

The crew of the car consisted of two - a driver-mechanic and a commander who was engaged in the maintenance of a machine gun or cannon.

The tank could be armed with a gun or a machine gun. The "cannon" version provided for the installation of a semi-automatic gun "Hotchkiss SA18" with a diameter of 37 mm. Guidance of the gun was carried out using a special shoulder rest, allowing you to perform vertical aiming in the range from -20 to +35 degrees.

The undercarriage of the tank was represented by track and support rollers, guide wheels, a screw track tensioning mechanism, which, in turn, were large-linked and had a lantern gear.

In the stern of the tank there was a bracket, thanks to which the vehicle was able to fell trees with a diameter of 0.25 meters, overcome trenches and ditches up to 1.8 meters wide and could withstand a roll at an angle of up to 28 degrees. The minimum turning radius of the tank was 1.41 meters.

End of World War I

During this period, General Etienne made an attempt to create independent tank troops, in which there should have been a division into light, medium and heavy vehicles. However, the general corps had its own opinion, and, starting from 1920, all tank squads were subordinated to the infantry. In this regard, a division into cavalry and infantry tanks appeared.

But still, Etienne's enthusiasm and activity were not in vain - until 1923, FCM created ten multi-turreted 2C heavy tanks. In turn, thanks to the FAMN company, the French branch of the M tanks appeared. The models of these vehicles were interesting in that they used both tracks and wheels at the same time. The type of engine could be changed depending on the surrounding circumstances.

Army motorization program

In 1931, France began to pay Special attention wheeled and reconnaissance vehicles. In this regard, Renault introduced the latest AMR light tank at that time. In this machine, the turret and hull were connected to each other with the help of a corner frame and rivets. Armored sheets were installed at a rational angle of inclination. The turret was shifted to the port side, and the engine to the right. The crew included two people. The standard armament was two machine guns - Reibel caliber 7.5 mm and large-caliber Hotchkiss (13.2 mm).

Extraordinary armored vehicle

The maximum development of French tanks fell on the period 1936-1940. It was connected with the growing military threat which the French military was well aware of.

One of the tanks that entered service in 1934 was the B1. Its operation showed that it had significant drawbacks: irrational installation of weapons in the hull, a high degree of vulnerability of the undercarriage, irrational distribution of functional responsibilities between crew members. Practice has shown that in reality the driver had to quit driving and supply ammunition. This led to the fact that in the end the tank became a stationary target.

In addition, the vehicle's armor caused particular criticism. French heavy tanks, like their counterparts in other countries of the world, have special requirements for their protection. B1 did not match them.

And finally, most importantly, the B1 was too expensive to build, operate and maintain. Of the positive qualities of the car, it is worth noting it high speed movement and good handling.

improved model

Considering French heavy tanks, you should definitely pay attention to the B-1 bis. The weight of this tank was 32 tons, and the armor layer was 60 mm. This allowed the crew to feel protected from German guns, with the exception of the Flak 36 88 mm anti-aircraft gun. The armament of the tank was also reinforced.

The armored car itself was assembled from cast parts. The tower was also produced by casting, and the hull was assembled from several armored sections, interconnected by bolts.

The CA-35 cannon with a caliber of 75 mm was used as a weapon, which was located on the right hand of the driver. Its elevation angle was 25 degrees, and declination - 15. In the horizontal plane, the gun had a rigid fixation.

Also available was a machine gun "Chatellerault" caliber 7.5 mm. It was fixed just below the gun. Both the driver and the tank commander could fire from it. In this case, an electric trigger was used.

It was possible to enter the tank through an armored door on the right side, hatches located in the turret and above the driver's seat, as well as through two emergency entrances - one was located in the bottom and the other on top of the engine compartment.

Also, this French tank was equipped with self-sealing fuel tanks and a directional gyroscope. The vehicle was driven by a crew of four. A distinctive feature of the car can be considered the presence of a radio station in it, which at that time was a rarity.

World War II period

French tanks of World War II were represented by the following vehicles:


Post-war days

The tank building program adopted in 1946 led to the fact that the best French tanks began to be produced.

In 1951, the AMX-13 light tank rolled off the assembly line. Its distinguishing feature was the oscillating tower.

The AMX-30 battle tank began to be produced in the 1980s. Its layout has a classic scheme. The driver is placed on the left side. The gunner and tank commander are located in the fighting compartment on the right side of the gun, while the loader sits on the right. The volume of fuel tanks is 960 liters. Ammunition is 47 shots.

Tank AMX-32 has a mass of 40 tons. The armament is a 120 mm cannon, a 20 mm M693 cannon and a 7.62 mm machine gun. Ammunition - 38 shots. On the highway, the tank is capable of speeds up to 65 km/h. There is no weapon stabilization system. In the presence of a digital ballistic computer, a laser rangefinder. For work at night, a Thomson-S5R camera paired with a gun is used. All-round visibility can be performed using eight periscopes. Also, the tank is equipped with a fire extinguishing and air conditioning system, an installation for creating smoke screens.

Export version

If the above models of French tanks were in service with France, then the AMX-40 tank was produced exclusively for export abroad. Guidance and fire control systems give a 90% chance of hitting a target, which can be at a distance of 2000 meters. At the same time, only 8 seconds pass from the moment of detection to the destruction of the target. The engine of the car is diesel, 12-cylinder, turbocharged. It is connected to a 7P automatic transmission, which allows it to develop 1300 hp. with., however, a little later the German transmission was replaced by a French counterpart. On the highway, the tank develops a speed of 70 km / h.

The era of modernity

To date, the newest French tank is the AMX-56 Leclerc. His mass production was started back in 1991.

The tank is characterized a high degree saturation of electronics, the total cost of which is equal to half the price of the entire machine. The layout of the tank is classic. The main armament is located in the tower.

The vehicle's armor is multi-layered and equipped with gaskets made of ceramic materials. The front of the case has a modular design, which makes it easy to change damaged parts.

The tank is also equipped with a system that protects the crew from weapons. mass destruction and a laser exposure alarm system.

The combat and engine compartments have high-speed fire extinguishing systems. A smoke screen can also be installed at a distance of up to 55 meters without any problems.

The main gun of the tank is the SM-120-26 120 mm cannon. In addition, there are two machine guns of different calibers. The combat weight of the vehicle is 54.5 tons.

D2 (French Char de bataille D2).

In 1929, the medium tank D-1, developed by Renault, was adopted by the French army. It was intended for direct support of the infantry and, like all "infantry" vehicles, it was distinguished by enhanced armor and low speed. Armor cast parts are widely used in the design. The turret is cast, in which a 47-mm cannon and a 7.5-mm machine gun are installed. In this case, the gun and machine gun had separate masks. Manually operated mechanisms were used to rotate the turret and aim the gun in a vertical plane. A tank telescopic sight was mounted for fire control. The undercarriage used 14 small diameter road wheels per side.

The first front rollers were auxiliary and worked when overcoming trenches, walls, etc. The second front rollers carried a small load from the weight of the machine, on flat hard ground they were unloaded, which improved the agility of the machine. The extreme rear rollers were intended to provide tension to the caterpillar, they did not carry the load from the weight of the machine. To protect the undercarriage, armored screens were hung. A modification of this vehicle (tank D2) began to be produced in 1936. Unlike the previous modification, it had a more powerful engine (150 hp instead of 100 hp on the D-1 tank) and enhanced armor. The maximum armor thickness has been increased to 40 mm. The weight increased accordingly: instead of 12 tons, it began to weigh 20 tons. The speed of movement increased slightly. Tanks D-1 and D-2 were produced until 1938. As of May 10, 1940, the troops had 213 units of these two types.

New french tank game world of Tanks appeared after update 9.7 and is called AMX 30 1er prototype. This is a Tier IX tank from the alternative French tech tree.

The combat unit is distinguished by dynamically selected characteristics with excellent maneuverability for a comfortable game and the presence of a good weapon. Armor AMX 30 one of the main weaknesses. With high-explosive shells, this French tank will only break through.
However, at the ultimate level of development, the prototype AMX 30 will give out armor penetration of 320 mm using HEAT projectile jets purchased with in-game gold.

- French premium heavy tank tier 8. New representative, available for in-game gold. - the site reminds that the maximum level of premium tanks in the game has a limit. You cannot buy French premium heavy tank above level 8. For this reason, premium tank FCM 50 t, which can be bought for 11900 gold, is an excellent farming machine.

Double the amount of credits and experience for each battle, together with an activated premium account, allows you to raise from 75,000 to 120,000 credits on a tank.

Characteristics FCM 50 t

As you already know, the introduction of a new premium tank into WOT was scandalous and long. Today unexpectedly Improved the main performance characteristics of the French premium tank AMX M4 mle.49, which additionally added discussions and conversations to this combat vehicle. At first, the AMX M4 mle.49 was not allowed into the game since the spring of 2017, then, after the release, the tanks began to receive complaints from players who purchased it for in-game gold, but in fact, as you well know, for real money.

Combat use SPG 10.5cm leFH18 B2 received while in occupied France in 1942. They were mainly used to fight partisans. Later, they repelled the Allied invasion of northern France in 1944. These self-propelled guns entered service with the tank and artillery units of the Wehrmacht.

Dear site readers!

World War II marked a bright spot on the map of Europe. General mobilization and the industrial boom of the military industry provoked a chain reaction and created different kinds combat vehicles. France did not stand aside from the general militarization and by the end of the war had weapons of significant quality and military equipment. Today we will take a closer look at French self-propelled guns Bat Chatillon 155.

Bat Chatillon 155 - French self-propelled artillery mount of the eighth level. It has a loading drum for 4 rounds, a slowly rotating turret, very good accuracy and dynamics. However, the penetration and damage are too low for the 8th level, and the long (over a minute) reloading of the drum leaves the artillery completely defenseless.

French self-propelled guns Bat Chatillon 155

A new French tier 8 heavy tank AMX M4 mle.49 has already been announced in World of Tanks, which will replace the main farm tank of this nation - the FCM 50t premium vehicle. According to the main performance characteristics, which are presented in the last screenshot (below), it follows that the AMX M4 mle.49 is better than the FCM 50t in almost all characteristics. Outperforms only in

  • movement speed
  • viewing range

Be that as it may, the tank will appear in , and as practice shows, they usually farm above any average premium at first. This is a Wargaming marketing ploy to motivate players to buy a new tank based on quick reviews of its profitability. Typically, such information is distributed among tankers like a virus. The conclusion is simple: if you want to farm a lot of credits quickly and easily, buy the AMX M4 mle.49 immediately, and not later.

- French heavy tank tier 9 in World of Tanks. They became the first tanks equipped with loading drums in World of Tanks. It is the presence of the loading drum that allows the AMX 50 120 to occupy one of the leading places among heavy tanks of the 9th level. Incredible DPM is able to turn almost any tank into a pile of scrap metal.

Fast, efficient, dangerous. Here are three characteristics of the French tank AMX 50 120.

Characteristics AMX 50 120

Char 2C(fr. Tank 2C, aka FCM2C) - . Developed during the First World War, but did not take part in hostilities. The Char 2C is the largest tank in terms of metric dimensions ever adopted in the world, and the second largest ever built (second only to the Russian Tsar Tank on a wheeled chassis). The tank was in service with the French army until the Second World War, but like the Soviet one close to it heavy tank The T-35 was not effective in any of the intended roles for tanks of this class (with the exception of the psychological impact on the morale of enemy troops).

Char 2C will appear in the game "World of Tanks" not soon. The developers left this tank for 2017. You can now see this French tank only in the one posted on ours.